Carrier PG95ESU User Manual Download

Page: 7 / 58

PG95ESU: Installation, Start-up, Operating and Service Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

body with static electricity (for example; DO NOT move or shuffle

your feet, do not touch ungrounded objects, etc.).

4. If you touch ungrounded objects (and recharge your body with

static electricity), firmly touch a clean, unpainted metal surface of

the furnace again before touching control or wires.

5. Use this procedure for installed and uninstalled (ungrounded)

furnaces.

6. Before removing a new control from its container, discharge your

body’s electrostatic charge to ground to protect the control from

damage. If the control is to be installed in a furnace, follow items 1

through 4 before bringing the control or yourself in contact with the

furnace. Put all used and new controls into containers before

touching ungrounded objects.

7. An ESD service kit (available from commercial sources) may also

be used to prevent ESD damage.

ACCESSORIES

See Product Data Sheet for a list of accessories for this product.

LOCATION

IMPORTANT:

Clearances for Condensate Trap. Before locating

furnace, refer to condensate trap installation instructions section for

required clearances for trap installation.

A200083

Fig. 6 – Trap Clearance in Horizontal Application

NOTE:

Local codes may require a drain pan and condensate tray when a

condensing furnace is installed over a finished ceiling.

A200084

Fig. 7 – Trap Clearance in Upflow Application

General

These furnaces are shipped with materials to assist in proper furnace

installation. These materials are shipped in the main blower

compartment.
Loose parts bag contents (

Table 2

This furnace must:

• be installed so the electrical components are protected from water.

• not be installed directly on any combustible material other than wood

flooring (refer to SAFETY CONSIDERATIONS).

• be located close to the chimney or vent and attached to an air

distribution system. Refer to Air Ducts section.

• be provided ample space for servicing and cleaning. Always comply

with minimum fire protection clearances (

Table 1

The following types of furnace installations may require OUTDOOR

AIR for combustion due to chemical exposures:

• Commercial buildings

• Buildings with indoor pools

• Laundry rooms

• Hobby or craft rooms

• Chemical storage areas
If air is exposed to the following substances, it should not be used for

combustion air, and outdoor air may be required for combustion:

• Permanent wave solutions

• Chlorinated waxes and cleaners

• Chlorine based swimming pool chemicals

• Water softening chemicals

• De-icing salts or chemicals

• Carbon tetrachloride

• Halogen type refrigerants

• Cleaning solvents (such as perchloroethylene)

• Printing inks, paint removers, varnishes, etc.

• Hydrochloric acid

• Cements and glues

• Antistatic fabric softeners for clothes dryers

• Masonry acid washing materials

All fuel-burning equipment must be supplied with air for fuel

combustion. Sufficient air must be provided to avoid negative pressure

in the equipment room or space. A positive seal must be made between

the furnace cabinet and the return-air duct to prevent pulling air from the

burner area.

CAUTION

PERSONAL RELIABILITY HAZARD

Failure to follow this caution may result in unit component damage.
Furnace may not be used for heating buildings under construction.

ADDITIONAL 1” CLEARANCE BELOW TRAP

RECOMMENDED FOR SERVICE

6-3/8”

Rubber elbow
or field supplied
PVC tee

Casing to elbow
or PVC tee = 3”
Casing with offset
adapter = 4-3/4”

WARNING

CARBON MONOXIDE POISONING / COMPONENT

DAMAGE HAZARD

Failure to follow this warning could result in personal injury or death

and unit component damage.

Corrosive or contaminated air may cause failure of parts containing flue

gas, which could leak into the living space. Air for combustion must not

be contaminated by halogen compounds, which include fluoride,

chloride, bromide, and iodide. These elements can corrode heat

exchangers and shorten furnace life. Air contaminants are found in

aerosol sprays, detergents, bleaches, cleaning solvents, salts, air

fresheners, and other household products. Do not install furnace in a

corrosive or contaminated atmosphere. Make sure all combustion and

circulating air requirements are met, in addition to all local codes and

ordinances.

Summary of Contents for PG95ESU



























































Search results

Summary of Contents for PG95ESU

Reviews:

Related manuals for PG95ESU

Brands by name

Popular brands

Carrier PG95ESU, User Manual

Search results

Summary of Contents for PG95ESU

Reviews:

Related manuals for PG95ESU

Brands by name

Popular brands