background image

To set up the controller through the Service port 

 

 

 

 
 

TruVu™ UC6

83T 

 

CARRIER CORPORATION ©2021   

Installation and Start-up Guide 

 

All rights reserved 

 

46 

 

You can communicate with the TV-UC683T through a web browser by connecting a computer to the controller's 

Service Port using either the Carrier wireless service adapter or a USB cable.  

NOTE

  You cannot access the Service port by plugging an Ethernet cable into Eth0 or Eth1. 

 

Once you are connected to the network, you can:  

 

Access the controller setup pages 

 

Address and configure controllers 

 

View the controller's Module Status report 

 

View/change controller and network settings. Changes take effect immediately. 

 

Troubleshoot 

 

Use BACnet/Service port to access the i-Vu® application or a touchscreen device. See 

To communicate 

through a BACnet/Service port network

 (page 46).  

  

 

 

To access the controller setup pages and use the 

Local Network

 tab, you must first connect to and manually 

address one TV-UC683T. For instructions on connecting, see 

Addressing the TV-UC683T through the Service port

 

(page 9). Navigate to http://local.access or http://169.254.1.1 to access the pages. Then set up the address on 

your selected TV-UC683T on the 

Ports

 tab

 (page 48)

 

NOTE

  The first time you access the controller in the i-Vu® interface, after you have changed settings through the 

Service port, be sure to upload the changes to the system database. This will preserve those settings when you 

download memory or parameters to the controller. 

 

 

 

ModStat tab 

This tab provides the controller's Module Status report that gives information about the controller and network 

communication status. See 

Appendix - Module Status field descriptions

 (page 66)

 

 

 

 

To set up the controller through the Service port 

Summary of Contents for TruVu UC683T











































































Reviews: