Recharging the jump-start unit with 230 VAC:
1.
Plug the 230V lead (14) into the adapter (6) and then into a 230 VAC
power outlet.
2
. Charge the jump-start unit up until the green charge indicator
comes on.
3.
This jump-start unit has an automatic cut-off so that you cannot
overcharge the battery.
Recharging the jump-start unit with 12 VDC:
Note: When recharging the jump-start unit in this way, it does not
reach the same voltage level as when recharging with 230 VAC.
1.
Put the 12 Volt charging cable (13) into the charging socket (6).
2.
Connect the charging cable plug (cigarette lighter plug) to a 12 V
cigarette lighter socket in your vehicle or boat.
Caution: Avoid explosive gases, flames and sparks.
Keep the area well ventilated while recharging the unit.
Circuit breaker:
In the event of an overload or short circuit at the 12
Volt output (2), the circuit breaker (7) is activated to prevent damage
to the Power Station Plus. After three minutes you can press it back
in again so that the Power Station may be used again.
LED light:
The Power Station has a built-in LED light to facilitate
working in the dark. This LED light is not suitable for lighting rooms
in the home.
Compressor
1.
Do not suck in any dirt or impurities, keep the ventilation slots
clear.
2.
Maximum operating time: 10 minutes. When using to inflate
several tyres, wait approx. 10 minutes in each case to allow the
compressor to cool down.
3.
Not suitable for inflating high-pressure tyres for trucks, tractors
or trailers.
4.
Do not use to blow air at people or animals, to not use to clean
clothes with compressed air.
Starting the compressor:
1.
Check pressure gauge before switching on.
2.
Switch on and off with toggle switch .
Run the compressor for max. 10 minutes at a time, then wait approx.
10 minutes before switching on again.
Inflating tyres:
Comply with your vehicle manual. First check the actual tyre pres-
sure with a calibrated inflation pressure gauge. Fit the connector
on the compressor tube over the valve and lock in place by shifting
lever . Inflate tyre to specified pressure, check pressure with
calibrated inflation pressure gauge.
Filling other objects:
Balls, cycle tyres etc. may be inflated by using the appropriate adapter
(in the flap on the side of the device ). Attach the adapter by moving
the lever on the compressor connector and inflate the item. To avoid
bursting the item do not overinflate it.
Cleaning:
Clean the device with a moistened soft cloth only when
disconnected from the electricity supply. Prevent liquids from penet-
rating the device.
Disposing of the battery
P
When the power unit battery no longer functions, it should be
recycled.
P
Please contact your local authorities for further information.
Do not dispose of this product in the household waste when the
charger stops working. You can find out more information from
your waste disposal services.
Warning:
Do not throw the battery into a fire: it could explode.
Before disposing of the battery, cover exposed contacts with insu-
lating tape to prevent any short circuit. Do not expose the
battery to either extreme heat or naked flames as this could cause an
explosion.
7
Operation
Observe the manufacturer’s instructions.
Warning: an electric shock can cause death or injury.
Do not touch exposed electric conductors.
Warning: When connecting and removing the jump-start cable
leads, make sure that they are not in contact with any rotating
parts of the engine.
Caution: Never allow the red and black terminals to touch each
other or another conductor.
DO NOT use Power Station immediately after charging. Let it stand
for at least ten minutes after charging and before restarting.
Before starting to use the device, make sure that the safety dial
(1) is in the “Off” (0) dial position and that the terminal clamps are
correctly attached.
This jump-start unit has been developed for use with vehicles and
boats with a petrol engine/motor of up to 3,000 cc or with a diesel
engine/motor of up to 2,000 cc. You will not need a host vehicle or
230 VAC power supply. You can also use this jump-start unit as a
portable 12 VDC power supply in remote areas or emergencies.
Proceed as follows to jump-start your vehicle:
1.
Make sure that the ignition of your vehicle or boat to be jump-star-
ted is not switched on. The parking brake must be activated. Manual
transmission in neutral, automatic transmission set to „P“. Connect
the red cable clamp to the positive terminal on the vehicle battery.
2.
Connect the black clamp to the car bodywork or to the negative
terminal of the vehicle battery.
3.
Set the safety switch (1) to „on“ (I).
4.
Turn the ignition key to the start position for no more than
5 seconds. If the engine does not start, wait for at least another
3 minutes before trying again. In low temperatures, several attempts
to start may be necessary. Always use the jump-start unit fully
charged, especially in low temperatures.
5.
Set the safety switch (1) to „off“ (O).
6.
Once the engine is running, disconnect the black clamp first and
put the lead back in its storage position in the jump-start unit.
7.
Disconnect the red clamp and put the lead back in its storage
position in the jump-start unit.
8.
Recharge your jump-start unit again as soon as possible.
Using the jump-start unit as power supply for other appliances
(lights, radios, etc.):
1.
Lift the cover on the cigarette lighter jack (2)
2.
Put the cigarette lighter plug of the appliance into the cigarette
lighter jack (2) of the jump-start unit.
Warning:
If the jump-start unit is not being used for starting
engines/motors, the safety dial located on the side should always
be in the OFF position (= switched off). In this position, the safety
switch prevents any electric shock from the red and black clamps.
Always keep the jump-start unit in a dry, safe place, out of reach of
children.
Do not use while travelling.
Store the Power Station at temperatures of between 15°C and 20°C
when it is not in use.
Recharging:
Only use the provided power pack to recharge the unit.
The battery of this unit can be recharged either with 230 VAC from
the mains power supply or 12 VDC from a cigarette lighter jack. It is
advisable to keep the battery fully charged at all times. Leaving the
battery on a low charge can shorten its service life. Please note that
the time it takes to recharge the battery depends on the number of
times the unit has been used for jump-starting. Press button (8) to
see whether the battery is flat. The indicator (4) shows the charge
status of the battery. „Green“ shows that the battery is adequately
charged. In temperatures below 3°C or above 40°C, in order to protect
the battery it is not possible to charge the Power Station.
B
A
C
D
77955-AZ-Profi-Powerstation-12V-CTR-IM-INT-OEF-170824.indd 6
24.08.17 10:24
