SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: sale@carymart.com
Press and hold button B: Turn on the relay 2, terminal OUT 2 outputs DC power, the lamp 2 is turned on.
Release button B: Turn off the relay 2, terminal OUT 2 no output, the lamp 2 is turned off.
3) Setting control mode Latched (with the transmitter C-3): Do not connect Jumper-1 and Jumper-2.
Press button A: Turn on the relay 1, terminal OUT 1 outputs DC power, the lamp 1 is turned on.
Turn off the relay 2, terminal OUT 2 no output, the lamp 2 is
turned off.
Press button B: Turn on the relay 2, terminal OUT 2 outputs DC power, the lamp 2 is turned on.
Turn off the relay 1, terminal OUT 1 no output, the lamp 1 is turned
off.
Press button C: Turn off the relay 2, terminal OUT 2 no output, the lamp 2 is turned off.
4) Setting control mode Mom Toggle (with the transmitter C-2): Connect Jumper-1 and Jumper-2.
Control mode Momentary (Channel 1):
Press and hold button A: Turn on the relay 1, terminal OUT 1 outputs DC power, the lamp 1 is turned on.
Release button A: Turn off the relay 1, terminal OUT 1 no output, the lamp 1 is turned off.
Control mode Toggle (Channel 2):
Press button B: Turn on the relay 2, terminal OUT 2 outputs DC power, the lamp 2 is turned on.
Press button B again: Turn off the relay 2, terminal OUT 2 no output, the lamp 2 is turned off.
Wired control terminals:
The receiver has wired control terminals, you can connect external devices, sensors, limit switches or manual switches to trigger the receiver.
1) By low level signal:
You can connect external devices (with low level output signal) to trigger the receiver.
When external device outputs low level signal to terminals 1 () and terminal 3 (Signal -), terminal of OUT1 output DC power, and the lamp 1 is
turned on.
When the external device stops to output signal, Terminal of OUT1 stop outputting, the lamp 1 is turned off.
When the external device outputs low level signal to manual terminal 2 and terminal 3, Terminal of OUT2 output DC power, the lamp 2 is turned on
When the external device stops to output signal, Terminal of OUT2 stop outputting, the lamp 2 is turned off.
2) By NO/NC contact:
You can connect manual switches (with NO/NC contact) to trigger the receiver.
When connect terminals 1 and 3 by manual switch, Terminal of OUT1 output DC power, the lamp 1 is turned on.
When disconnect terminals 1 and 3 by manual switch, Terminal of OUT1 stop outputting, the lamp 1 is turned off.
When connect terminals 2 and 3 by manual switch, Terminal of OUT2 output DC power, the lamp 2 is turned on.
And when disconnect terminals 2 and 3 by manual switch, Terminal of OUT2 stop outputting, the lamp 2 is turned off.
How to pair the transmitter to the receiver:
1) Press the learning button of receiver for 1- 2 seconds; signal LED on the receiver is on. The receiver enters into status of LEARNING.
2) Press any one button on transmitter. If signal LED flashes quickly 15 times and turns off, it means learning is successful.
3) When receiver is in the status of LEARNING, press again the learning button, signal LED turns off, learning process will be discontinued.
4) The receiver can learn several remote controls with different codes.
Delete all transmitters:
We have learned remote control to
the receiver. If you don’t want the receiver to work with the remote control, you can delete all codes of remote
controls, which are stored in the receiver.
Operation: Press and hold the learning button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all
stored codes have been deleted successfully.
