10 Printer Hardware Settings
34
< CAL: PRINTER HARDWARE SETTINGS >
1. PRINTER SENSORS
2. PRINT SPEED
3. PRINTER ODOMETER
4. LABEL TYPE
5. ADJUST FEED LENGTH
< CAL: PRINTER SENSORS >
1. GAP/PEEL CALIBRATE
2. FINE GAP ADJUST
3. FINE PEEL ADJUST
< CAL: PRINTER SENSOR CALIBRATION >
Load Printer With Gapped Labels
Press any key when ready.
GAP= 100 PEEL= 151
10 Printer Hardware Settings
10.1 Printer Hardware Settings Menu
Once at the CAL Main
menu screen, press the 4 key. The
Printer Hardware Settings Menu
screen will appear as follows.
10.2 Printer Sensors
At the Printer Hardware Settings
Menu screen, press the 1 key for
Printer Sensors. The Printer Sensors
Menu screen will then appear as
follows:
Gap/Peel Calibrate:
This is an
automated process that
calibrates both sensors. Please
make sure that there are non-continuous labels in the printer, that the labels are installed properly, and
that the print head is locked down.
Using continuous labels will not calibrate the Gap sensor.
Fine Gap Adjust:
This is a manual process that allows you to change the Gap sensor threshold value
directly.
Fine Peel Adjust:
This is a manual process that allows you to change the Peel sensor threshold value
directly. This process also lets you actively test your setting.
Gap Sensor:
This is the sensor that is used to sense the spaces between the labels (gaps.) It is
responsible for top-to-bottom alignment of your print.
Peel Sensor:
This is the sensor that is used to sense if there is a printed label waiting to be picked up by
the user. If there is a printed label waiting to be picked up, this sensor will prevent another label from
printing. It will display an error message on the t op right of the screen: “PEEL”.
10.2.1 Gap/Peel Calibrate
At the Printer Hardware
Settings Menu screen, press the 1
key for Printer Sensors. The Printer
Sensors Menu screen will then
appear. At the Printer Sensors
Menu screen, press the 1 key for
Gap/Peel Calibrate. You will see
the following screen:
Once ready, press any key.
Summary of Contents for LP-2G
