background image

www.CasablancaFanCo.com

1.888.227.2178

Wiring

FRO

M FAN

FR

OM

 CEILING BRA

CK

ET

FROM FAN

Using an orange wire 

connector from 

the        hardware 

bag, connect the 3 

grounding wires (green, 

green/yellow stripe, or 

bare copper) coming 

from the ceiling, fan, 

and hanging bracket. 

(G

rounding)

G

reen/Y

ello

Strip
e

Green/Yellow 

Stripe

W

hit

e

Black

(G

rounded)

Note: To connect the wires, 

hold the bare metal leads 
together and place a wire 

connector over them, then twist 

clockwise until tight.

Using the orange wire 

connectors from 

the        hardware bag, connect 

the black wire (ungrounded) 

from the ceiling to the black 

and the blue wires from the 
fan. Connect the white wire 

(grounded) from the ceiling to 

the white wire from the fan.  

Using the orange wire 

connectors from 

the        hardware bag, 

connect the white wire 

(grounded) from the 

ceiling to the white wire 

from the fan.

Connect the black wire 

(ungrounded) from the 

ceiling to the black wire 

from the fan. Connect the 

second (ungrounded) wire 

from the ceiling to the blue 

wire from the fan.

FROM FAN

Whit

e

  

(Ungr

ounded)

Black

Blue

(Grounded

)

FR

OM CEILING

   

(Ungrounded

)

Blue

For Dual Switches

For a Single Switch

 

FR

OM CEILING

Turn the splices upward and push them carefully back through the hanger bracket 

into the outlet box. Spread the wires apart, with the grounded wires on one side of 

the outlet box and the ungrounded wires on the other side of the outlet box.

Refer to CAUTION c.1 on pg. 2 

 

FR

OM CEILING

 

7

M6017-01 • 04/11/13 • © Casablanca Fan Company

(Ung

rounded)

Summary of Contents for Durant 54101















Reviews: