background image

1

4

3-SPEED 

 W-8 WALL CONTROL OF THE FAN & LIGHT(S)

3-SPEED 

 W-4 WALL CONTROL OF THE FAN

R

• The fan may be turned ON and OFF

by the W-8 wall control.

• The lights may be turned ON and

OFF by the W-8 and the intensity
adjusted from low to high.

• The fan must be supplied with two

independent 120V AC supply
wires.

• Set the FAN pull chain switch to

the HIGH speed setting.

• Turn the lights ON at the fan.
• The W-8 allows the choice of four

(4) different speed settings.

• The W-4 allows the choice of four (4)

different speed settings.

• No light fixture is used.
• Set the FAN pull chain switch to the

HIGH speed setting.

• No changes in household or fan wiring

are required.

• The fan may be turned ON and OFF by

the W-4 wall control.

CAUTION! Failure to set the pull-chain

speed to HIGH can result in faulty

operation of the fan and damage to

the W-4 wall control. To confirm fan

is set to HIGH: Turn W-4 fan speed

switch to 'HI' - set fastest fan speed

with pull chain.

CAUTION! Failure to set the pull-

chain speed to HIGH can result in

faulty operation of the fan and

damage to the W-8 wall control.

To confirm fan is set to HIGH: Turn

W-8 fan speed switch to 'HI' - set

fastest fan speed with pull chain.

3-SPEED

Summary of Contents for FOUR SEASONS III


















Reviews: