background image

GETTING STARTED

Installing a New Ceiling Fixture Outlet Box

If you do not have an existing fi xture located where you wish 

to place your Casablanca fan, an approved ceiling fi xture 

outlet box must be installed and wired.

Using Existing Ceiling Fixture Outlet Box

After turning the power OFF at its source (either the circuit 

breaker or fuse box), lower the old fi xture and disconnect the 

wiring. Check the ceiling fi xture outlet box to be sure that 

it is marked “Approved For Ceiling Fan Mounting.” If it is 

not, a new box must be installed.
NOTE: Th e weight of this fan is 50 pounds.

Wire Nut (4)

ADDITIONAL HARDWARE

2

1

/4

 x 8-32 Rounded Head Screw (2)

Flat Washer (2)

1

 x 8-32 Rounded 

Head Screw (2)

Large Flat Washer 

3

/

8

(1)

Crossbar Mounting Bracket

Lag Screw     

3

/

8

 #7 x 5

 (1)

Ceiling 
Wiring

Crossbar Mounting 

Bracket

Green Ground Wire

Ceiling-Fan-Approved

Wiring Box

Ridge side down

NOTE: 

After removing the old fi xture, check the outlet box 

to ensure it is supported by a joist or beam across its upper 

surface. If not, a 2 x 4 stud must be installed.

Step 1a.

 Remove the knockout plug in the center of the 

outlet box or drill a 

1

/

2

-inch hole for the lag screw to pass 

through. Th en drill a 

1

/

4

-inch guide hole into the joist or 

beam to a depth of 3 inches.

Step 1b.

 Route the outlet box wires through the center 

hole of the crossbar mounting bracket. Attach the crossbar 

mounting bracket to the outlet box with the screws provided, 

ensuring that the outlet box wires are not pinched by the 

washer. 

CROSSBAR MOUNTING BRACKET INSTALLATION

CEILING HARDWARE 

(not to scale)

4

FAN INSTALLATION

APPROVED OUTLET BOX 
HARDWARE

CAUTION:  To reduce the risk of personal injury, 

use only the mounting hardware provided with the 

approved outlet box to install the crossbar mounting 

bracket.

WARNING: To reduce the risk of fire, electrical 

shock, or personal injury, mount to outlet box marked 

“Acceptable for Ceiling Fan Support” using the 

mounting hardware provided with the outlet box.

WARNING!

Support directly to building structure only.

Summary of Contents for Seacoast

















Reviews: