8
and inexorably affect the duration of the
appliance’s useful life and could become
unsafe to use.
Supplies
- Always use original supplies, designed
specifically for your appliance model.
- These supplies are available in specialist
shops.
Anomalies and repair
- Take the appliance to an authorised
technical support service if a product
damage or other problems arise. Do not try
to dismantle or repair without assistance, as
this may be dangerous.
- If the connection to the mains has been
damaged, it must be replaced and you
should proceed as you would in the case of
damage.
Specifications:
VMP800M
- Rated power (W):
800
- Rated Voltage
230V~
- No load speed (rpm):
900
- Blows per minute (ipm)
3900
- Impact Energy (J)
4
- Maximum capacity in concrete (mm)
26
- Weight (Kg:)
3.8
- Sound Pressure level (LpA) =89,3dB(A), KpA = 3 dB
- Sound Power level (LwA) = 100,3 dB(A), KWA = 3 dB
- Vibration=
19,2 m/s2, K=1,5 m/s2
NB: These specifications are subject
to change without notice of purpose of
improvement.
NB: By virtue of the conditions of fabrication
of this product, the maximum absorbed
power can differ from that specified.
- Turn the selector (C) until the arrow on the
appliance points to
( )
- Place the appliance against the surface you
want to work.
- Press the appliance until the lengthways
play is taken up.
- Turn the appliance on, by using the on/off
button (E).
Note: Exerting high pressure does not
increase machine effectiveness!
WARNING:
When the bit begins to
penetrate concrete or comes up against
the reinforcement rods in the concrete, the
tool may react dangerously. Make sure
you keep your balance by distributing your
weight evenly and keeping your feet in a safe
position whilst holding the tool firmly in both
hands to avoid dangerous reactions.
Once you have finished using the
appliance:
- Stop the appliance by releasing the on/off
switch (E).
Lubrification (Fig 1)
- After approximately 50 hours the machines
must be lubricated.
- Open the cover if the lubrication point (G)
using a key.
- Apply an appropriate amount of grease to
the mechanism.
- Close the cover (G).
Replace the carbon Brush (Fig 1)
- Unplug the appliance from the mains.
- The motor employs carbon brushes that
are consumable parts; since an excessively
worn carbon brush could result in motor
trouble.
- Remove the Carbon brush cap (H) and the
brush Cover.
- Replace the carbon brush.
- Reassemble the brush Cover and the
carbon brush cap.
WARNING:
When the bit begins to
penetrate concrete or comes up against
the reinforcement rods in the concrete, the
tool may react dangerously. Make sure
you keep your balance by distributing your
weight evenly and keeping your feet in a safe
position whilst holding the tool firmly in both
hands to avoid dangerous reactions.
Cleaning
- Disconnect the appliance from the mains
and allow it to cool before undertaking any
cleaning task.
- Allow it to cool before undertaking any
cleaning task.
- Clean the electrical equipment and the
mains connection with a damp cloth and dry.
DO NOT IMMERSE IN WATER OR ANY
OTHER LIQUID.
- Clean the equipment with a damp cloth with
a few drops of washing-up liquid and then
dry.
- Do not use solvents, or products with an
acid or base pH such as bleach, or abrasive
products, for cleaning the appliance.
- Do not let water or any other liquid get into
the air vents to avoid damage to the inner
parts of the appliance.
- Never submerge the appliance in water
or any other liquid or place it under running
water.
- If the appliance is not in good condition
of cleanliness, its surface may degrade
Summary of Contents for VMP800M
Page 1: ...VMP800M ...
Page 68: ......
Page 69: ......
Page 70: ...CASALS POWER TOOLS S L Av Barcelona s n 25790 Oliana SPAIN EU www casalstools es ...
