TECHNICAL DATA
Mitre saw
VNTR250M
Absorbed power
W
1800
No-load speed
rpm
4
5
00
Cut with base at 0º and head at 90º / mitre (AxB Fig.7a)
mm
75x130
Cut with base at 0º and head at 45º / mitre (AxB Fig.7b)
mm
52x130
Cut with base at 45º and head at 45º / mitre (AxB fig.7c)
mm
52x90
Cut on upper bench
mm
0-40
Blade diameter
mm
250
Blade hole diameter
mm
30
Weight
Kg
16
Acoustic pressure, Lpa
dBA
93
Sound power emitted, Lwa
dBA
106
Vibration level (according to ISO 8041 and ISO 5348)
m/seg
2
3,1
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at
hand to use w hen carrying out maintenance on the
indicated parts.
If the tool is used with care and a normal maintenance is
carried out, it will have a long life.
GENERAL INFORMATION
IDENTIFICATION (See indicated figures)
A Uptake connection nozzle (Fig.1)
B Pushbutton switch (Fig.3)
C Safety hook release button (Fig.1)
D Upper table power ON switch (Fig.1)
E Upper table power OFF switch (Fig.1)
F Upper bench saw protector (Fig.2)
G Upper bench (Fig.2)
H Saw protector and upper table block (Fig.6)
I
Saw blade (Fig.1 and 4)
J Mobile guard (Fig.1 and 4)
K Turntable (Fig.1)
L Base (Fig.1)
M Fixed guide (Fig.1)
N Turn table blocking knob (Fig.1)
O Motor group blocking handle (Fig.5)
P Position lock pin (Fig.5 and 6)
Q Table height regulating knob (Fig.5)
R1 Graduated scale for turning the motor unit (Fig.5)
R2 Graduated scale turntable (Fig.1)
S Guide fixing butterfly (Fig.1)
T Upper bench guide (Fig.1)
U Tracking device (Fig.1)
V Saw penetration adjustment screw (Fig.5)
Z Adjustment bolt (Fig.5)
Z1 Adjustment bolt (Fig.1)
Z3 Clamp (Fig.1)
TECHNICAL CHARACTERISTICS
The robust and highly reliable structure makes these
mitres suitable for cutting wood and aluminium in indus-
trial environments, while preserving their usual ease of
handling and without restricting their movement.
These models are fitted with a w ide upper table that
allows the mitre saw to be transformed into a table saw
to carry out cutting.
The tool has been designed and built so that it is possi-
ble to work in all situations with total safety, however, in
special working conditions, glov es and protectiv e gog-
gles should be worn.
The tool has been designed and built to reduce noise
to a minimum (see technical data), however, in special
conditions the max imum noise lev el in the workplace
might exceed 85 dB (A). In this case, the operator
should protect himself from ex cessive noise by using
ear protectors.
GENERAL SAFETY REGULATIONS
See manual
‘Safety instructions’
which is supplied
together with this instructions manual.
INSTALLATION
1. ELECTRICAL CONNECTION
Before connecting the machine to the mains, one must
make sure that it complies with current regulations in the
country where it is used and that the voltage and fre-
quency are as indicated on the characteristics plate.
When extensions are used, make sure that the cross
section of the cables is suited to their length. If using roll
up extensions, make sure that they unroll completely in
order to prevent overheating.
2. WORKPLACE
The tool that you have purchased is a transportable or
semi-stationary electric tool. O nly one operator is
needed to use it, giv en its structure, w eight and ease
of handling.
In normal use, the operator is in front of the machine
with the handle to his right. The right hand on the handle
allows the machine to be handled completely, in fact, the
switch and a safety hook may be accessed w ithout
releasing the handle.
MITRE SAW ADJUSTMENT - SQUARING
The mitre is deliv ered by the manufacturer already
adjusted and squared according to standard parameters.
WARNING – b efore making any adjustment of the
mitre, unplug the machine.
1. BLADE UNIT LIFTING
An internal spring keeps the motor unit at rest position
(raised).
In this position, a safety hook prev ents the unit from
being activated accidentally.
