INTRODUCTION
Torque ( - A.90.A.10)
435, 445
BOLT TORQUE INFORMATION
DECIMAL HARDWARE
1.
Fasteners should be replaced with the same or higher grade. If higher grade fasteners are used, these
should only be tightened to the strength of the original.
2.
Make sure the fasteners threads are clean and that thread engagement is started. This will prevent them from
failing when being tightened.
3.
Tighten plastic insert or crimped steel-type lock nuts to approximately
50 %
of the dry torque, applied to the
nut, not to the bolt head. Tighten toothed or serrated-type lock nuts to the full torque value.
4.
The L9 (Alloy) fasteners torque values are for a bolt, nut, and two washers. When using L9 (Alloy) fasteners,
do not use the values in this table for tapped holes.
GRADE
1 or 2
5
5.1
5.2
8
8.2
L9 (Alloy)
SAE Markings
for Bolts and
Cap Screws
2
5
8
L9 (Alloy)
SAE Markings
for Hex Nuts
GRADE 2 *
GRADE 5, 5.1 or 5.2
GRADE 8 or 8.2
GRADE L9 (Alloy)
Dry **
Lubricated
**
Dry**
Lubricated
**
Dry**
Lubricated
**
Head
Nut
SIZE Nm
lb/ft
Nm
lb/ft
Nm
lb/ft
Nm
lb/ft
Nm
lb/ft
Nm
lb/ft
Nm
lb/ft
Nm
lb/ft
1/4
UNF
7.5
5.5
5.7
4.2
10.8 8
8.5
6.3
16.3 12
12.2 9
13.6 10
14.9 11
1/4
UNC
8.5
6.3
6.4
4.7
13.6 10
9.8
7.2
19
14
13.6 10
16.3 12
17.6 13
5/16
UNF
15
11
11
8
23
17
18
13
33
24
24
18
26
19
28
21
5/16
UNC
16
12
12
9
26
19
19
14
37
27
27
20
27
20
31
23
3/8
UNF
27
20
20
15
41
30
31
23
61
45
47
35
41
30
45
33
3/8
UNC
31
23
23
17
47
35
34
25
68
50
47
35
47
35
52
38
7/16
UNF
43
32
33
24
68
50
47
35
95
70
68
50
75
55
81
60
7/16
UNC
49
36
37
27
75
55
54
40
108
80
81
60
81
60
88
65
1/2
UNF
68
50
47
35
102
75
75
55
149
110
108
80
115
85
129
95
1/2
UNC
75
55
54
40
115
85
88
65
163
120
122
90
129
95
142
105
9/16
UNF
95
70
75
55
149
110
108
80
203
150
149
110
163
120
190
140
9/16
UNC
108
80
81
60
163
120
122
90
231
170
176
130
183
135
203
150
6-75491 1 04/05/2005
7
Summary of Contents for 435
