background image

Safety, general information and standard torque data

WARNING

Lower all attachments to the ground or use stands to safely support the attachments before you do any
maintenance or service.

WARNING

Pin sized and smaller streams of hydraulic oil under pressure can penetrate the skin and result in serious
infection.
If hydraulic oil under pressure does penetrate the skin, seek medical treatment immediately.
Maintain all hoses and tubes in good condition.
Make sure all connections are tight.
Make a replacement of any tube or hose that is damaged or thought to be damaged.
DO NOT use your hand to check for leaks, use a piece of cardboard or wood.

WARNING

When removing hardened pins such as a pivot pin, or a hardened shaft, use a soft head (brass or bronze)
hammer or use a driver made from brass or bronze and a steel head hammer.

WARNING

When using a hammer to remove and install pivot pins or separate parts using compressed air or using
a grinder, wear eye protection that completely encloses the eyes (approved goggles or other approved
eye protectors).

WARNING

Use suitable floor (service) jacks or chain hoist to raise wheels or tracks off the floor.
Always block machine in place with suitable safety stands.

WARNING

When servicing or repairing the machine, keep the shop floor and operator's compartment and steps
free of oil, water, grease, tools, etc.
Use an oil absorbing material and/or shop cloths as required.
Use safe practices at all times.

WARNING

Some components of this machine are very heavy.
Use suitable lifting equipment or additional help as instructed in this Service Manual.

WARNING

Engine exhaust fumes can cause death.
If it is necessary to start the engine in a closed place, remove the exhaust fumes from the area with an
exhaust pipe extension.
Open the doors and get outside air into the area.

WARNING

When the battery electrolyte is frozen, the battery can explode if (1), you try to charge the battery, or (2),
you try to jump start and run the engine.
To prevent the battery electrolyte from freezing, try to keep the battery at full charge.
If you do not follow these instructions, you or others in the area can be injured.

84402832 NA - May 2011

1001-5

Summary of Contents for CX250C
























Reviews: