Operation Guide 4700
3
Alarm
When the alarm is turned on, the alarm sounds when the
alarm time is reached. You can also turn on an Hourly
Time Signal, which will cause the watch to beep twice
every hour on the hour.
•
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing
C
.
Alarm time
(Hour : Minutes)
Hourly time signal
on indicator
Alarm on indicator
To set the alarm time
1. In the Alarm Mode, hold down
A
until the hour setting of the alarm time starts to
flash, which indicates the setting screen.
•
This operation automatically turns on the alarm.
2. Press
C
to move the flashing between the hour and minute settings.
3. While a setting is flashing, use
D
(+) and
B
(–) to change it.
•
When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (
P
indicator).
4. Press
A
to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds, regardless of the mode the
watch is in.
•
To stop the alarm tone after it starts to sound, press any button.
To test the alarm
In the Alarm Mode, hold down
D
to sound the alarm.
Alarm Off
Signal Off
Alarm On
Signal Off
Alarm Off
Signal On
Alarm On
Signal On
Alarm On Indicator / Hourly Time Signal On Indicator
To turn the Daily alarm and the Hourly Time Signal on and off
In the Alarm Mode, press
D
to cycle through the settings shown below.
•
The alarm on indicator and the Hourly Time Signal on indicator are shown on the
display in all modes while these functions are turned on.
Illumination
An LED (light-emitting diode) and light guide panel
illuminate the digital display for easy reading in the dark.
•
See “Illumination Precautions” for other important
information.
To turn on illumination
In any mode, press
B
to illuminate the display.
Timekeeping
Use the Timekeeping Mode to set and view the current time and date. This section
also explains how to manually set the current date and time.
•
All of the operations in this section are performed in the Timekeeping Mode, which
you can enter by pressing
C
.
▲
Press
A
.
Hour : Minutes
PM indicator
▲
A
Day of week
Day
Setting the Digital Time and Date Manually
Make sure you select your Home City code before you change the current time and
date settings. World Time Mode times are all displayed in accordance with the
Timekeeping Mode settings. Because of this, World Time Mode times will not be
correct if you do not select the proper Home City code before setting the time and
date in the Timekeeping Mode.
|
|
||
below to select other settings.
City code
3. When the setting you want to change is flashing, use
B
and/or
D
to change it as
described below.
Seconds
Hour
12/24-Hour
Format
Minutes
Year
DST
Day
Month
City Code
Screen:
To do this:
Change the city code
Cycle between Daylight Saving Time
(
ON
), Standard Time (
OFF
), and
Auto DST (
)
Toggle between 12-hour (
12H
) and
24-hour (
2
4
H
) timekeeping
Do this:
Use
D
(east) and
B
(west).
Press
D
.
Press
D
.
Reset the seconds to
Change the hour or minutes
Change the year
Change the month or day
Press
D
.
Use
D
(+) and
B
(–).
•
See “City Code Table” for a complete list of available city codes.
4. Press
A
to exit the setting screen.
•
When you exit the setting screen, the analog hands are adjusted automatically to
match the digital time. See “Analog Timekeeping” for more information.
Note
•
Auto DST (
) can be selected only while
LIS
,
LON
,
BCN
,
MAD
,
PAR
,
MIL
,
ROM
,
BER
,
STO
,
ATH
, or
MOW
is selected as the Home City code. For more information,
see “Daylight Saving Time (DST)” below.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the digital time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight Saving
Time.
The time calibration signal transmitted from Rugby and Mainflingen includes both
Standard Time and DST data. When the Auto DST setting is turned on, the watch
switches between Standard Time and DST (summer time) automatically in
accordance with the received time signal.
•
Auto DST (AUTO) can be selected only while
LIS
,
LON
,
BCN
,
MAD
,
PAR
,
MIL
,
ROM
,
BER
,
STO
,
ATH
, or
MOW
is selected as the Home City code.
•
The default DST setting is Auto DST (
) whenever you select
LIS
,
LON
,
BCN
,
MAD
,
PAR
,
MIL
,
ROM
,
BER
,
STO
,
ATH
, or
MOW
as your Home City code.
•
If you experience problems receiving the time calibration signal in your area, it is
probably best to switch between Standard Time and Daylight Saving Time (summer
time) manually.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down
A
until the city code starts to flash, which
indicates the setting screen.
2. Press
C
once and the DST setting screen appears.
3. Use
D
to cycle through the DST settings in the sequence shown below.
Auto DST (
)
DST off
DST on
4. When the setting you want is selected, press
A
to exit the setting screen.
•
The DST indicator (
) appears on the display to indicate that Daylight Saving Time
is turned on.
Analog Timekeeping
The analog time of this watch is synchronized with the digital time. The analog time
setting is adjusted automatically whenever you change the digital time.
Note
•
The hands for the analog timepiece move to adjust to a new setting whenever any of
the following occurs.
When you change the digital time setting manually
When the digital time setting is changed by time calibration signal reception
When you change the Home City code and/or DST setting
•
If the analog time does not match the digital time for any reason, use the procedure
described under “To adjust the analog time” to match the analog setting to the digital
setting.
•
Whenever you need to adjust both the digital and the analog time settings manually,
make sure you adjust the digital setting first.
•
Depending on how much the hands have to move in order to adjust to the digital
time, it may take some time before they stop moving.
To adjust the analog time
1. In the Timekeeping Mode, press
C
five times to enter
the Hand Setting Mode.
2. Hold down
A
until the current digital time starts to
flash, which indicates the setting screen.
3. Use
D
and
B
to adjust the analog setting as
described below.
When you want to do this:
Move the hand setting
forward 20 seconds
Move the hand setting a short
way forward at high speed
Perform this button operation:
•
Press
D
.
•
Hold down
D
.
•
Release
D
when the hands reach the setting
you want.
|
|
|
|
|
| | |
Move the hand setting a
long way forward at high
speed
•
While holding down
D
to move the hands at
high speed, press
B
to lock the high-speed
hand movement.
•
To stop the hand movement, press any
button.
•
Hand movement stops automatically if the hour
hand makes one full (12-hour) revolution.
|
|
||
|
| | | |
To set the current digital time and date manually
1. In the Timekeeping Mode, hold down
A
until the city
code starts to flash, which indicates the setting screen.
2. Press
C
to move the flashing in the sequence shown
below to select other settings.
City code
4. Press
A
to exit the setting screen.
•
The minute hand will be adjusted slightly to match the seconds when you exit the
setting screen.
•
To return to the Timekeeping Mode, press
C
.
