EN
ELECTRICAL HAZARD
Risk from electrical current!
In case of improper installation, the device can be dangerous and cause injury. Before installation, check the
power system data. Connect the device only when there is compliance. The unit should be unpacked and
checked fully before connecting by a professional.
5.2 Use
WARNING
The establishment of the installation of the device and maintenance must be performed only by professionals.
• Do not leave the unit without monitor.
• During use, your hands should be dry.
• Do not move or tilt the device during operation.
MANUAL
COMMISSIONING
The unit must be completely removed from its packaging. All guards must be fully
withdrawn.
Place the machine upright on a solid, flat surface. Never put the unit on a flammable surface.
Do not install this device near open fires or other heating appliances.
It is prohibited to place on the device or in the distance less than 10 cm of the device flammable objects.
The safety distances for flammable materials according to their degree of flammability:
A nonflammable granite, sandstone, concrete, brick, ceramic tile, coating.
B flammability acumin, jefferson, lihnos, itaver
C1 poorly flammable wood Hardwoods trees, against-plated, hardened paper umakart
C2 average flammability chipboard solodur, cork, rubber, coatings
C3 easy flammability of wood fiber boards, polystyrene, plyurethène, PVC
The electric cable must be protected at least 16 amperes.
The device must be plugged directly into a wall outlet.
Using a power strip will crack up the device.
USE
Connect the equipment. The red light comes on.
Set the machine using the thermostat knob to the desired temperature. The green LED turns on and the
heating element.
The setpoint temperature is between 60 and 80 ° C and the apparatus takes about 20-25 minutes to reach
it.
The green light goes off when the desired temperature is reached, the thermostat switches on again as
soon as the temperature drops.
To switch off set the temperature control to "0".
Always unplug the device when the device is not used.
NOTE
The device has a security system in case of overheating. Upon activation, disconnect the device and allow it
to cool. If this protection system will start regularly, it is imperative to contact your dealer.
After automatic shutdown, the unit may be commissioned only by pressing the reset button on the unit's back
for this, wait until the temperature drops, press the Reset button.
6. CLEANING AND MAINTENANCE
6.1 Safety Precautions
All maintenance, cleaning, appliance repair must be done with an unplugged (isolated from all electrical
sources).
The use of caustic detergents and baking soda for cleaning is forbidden. The water does not get inside the
unit.
Summary of Contents for 3611630043366
