background image

OPERATION

TS--2700/TS--3300 (05--04)

3

SAFETY PRECAUTIONS

This machine is intended for commercial use. It is

designed exclusively to scrub hard floors in an

indoor environment and is not constructed for any

other use. Use only recommended pads, brushes

and commercially available floor cleaners

intended for machine application.
All operators must read, understand and practice

the following safety precautions.

The following warning alert symbol and the “FOR

SAFETY” heading are used throughout this manual as

indicated in their description:

WARNING: To warn of hazards or unsafe

practices which could result in severe personal

injury or death.
FOR SAFETY: To identify actions which must be

followed for safe operation of equipment.

Failure to follow these warnings may result in:

personal injury, electrical shock, fire or explosion.

WARNING: Fire Or Explosion Hazard. Never

Use Flammable Liquids Or Operate Machine In Or

Near Flammable Liquids, Vapors Or Combustible

Dusts.
This machine is not equipped with explosion

proof motors. The electric motors will spark upon

start up and during operation which could cause a

flash fire or explosion if machine is used in an

area where flammable vapors/liquids or

combustible dusts are present.

WARNING: Fire Or Explosion Hazard. Do Not

Pick Up Flammable Materials Or Reactive Metals.

WARNING: Fire Or Explosion Hazard.

Batteries Emit Hydrogen Gas. Keep Sparks And

Open Flame Away. Keep Battery Compartment

Open When Charging.

WARNING: Electrical Hazard. Disconnect

Battery Cables Before Servicing Machine.

The following information signals potentially

dangerous conditions to the operator or

equipment:
FOR SAFETY:
1. Do not operate machine:

--

With flammable liquids or near flammable

vapors as an explosion or flash fire may

occur.

--

Unless trained and authorized.

--

Unless operation manual is read and

understood.

--

If not in proper operating condition.

2. Before starting machine:

--

Make sure all safety devices are in place

and operate properly.

3. When using machine:

--

Go slow on inclines and slippery surfaces.

--

Wear no--slip shoes.

--

Use care when reversing machine.

--

Report machine damage or faulty

operation immediately.

--

Never allow children to play on or around.

--

Follow mixing and handling instructions

on chemical containers.

4. Before leaving or servicing machine:

--

Stop on level surface.

--

Turn off machine.

5. When servicing machine:

--

Avoid moving parts. Do not wear loose

jackets, shirts, or sleeves.

--

Block machine tires before jacking up.

--

Use hoist or jack that will support the

weight of the machine.

--

Wear eye and ear protection when using

pressurized air or water.

--

Disconnect battery connections before

working on machine.

--

Wear protective gloves and safety glasses

when handling batteries or battery cables.

--

Avoid contact with battery acid.

--

Use manufacturer supplied or approved

replacement parts.

--

All repairs must be performed by a

qualified service person.

--

Do not modify the machine from its

original design.

Summary of Contents for TS-2700














































Reviews: