2.
Parts list
3#Motors
Battery V+
1
#
Motors
2
#
Motors
4
#
Motors
FPV aircraft br ushless electronics
speed controller instr uction manual
3.
Spec
4.
Notice
1.
Connection diagram
Silicone shock absorber strut
Xt60 power line
10P & 10P silicone harness
electrolytic capacito
10P & 10P silicone harness, apply to Tmotor F722 Flight Controller.
Please weld the electrolytic on the anode and cathode to get better filtering
effect.
For express setup, please confirm if the line order of harness andflight
controller port is corresponding. If not, please modify the wireto apply to
your flight controller.
Model
Current
Peak current
Lipo
Weight
Size
Mounting hole
Parameter
tuning software
ESC Firmware
Typical application
170-450 multi-rotor
Each time ESCs are connected to the system,input throttle signal will be detected
automatically when powered on and execute corresponding throttle mode.
When BLDC motor is connected to the system for the first time, or RC equipment
is changed, throttle calibration is required. Please skip throttle range calibration
when input signal is Dshot mode.
Don't flash any other firmwares to avoid esc damage.
Please repeatedly check the polarity before power up.
Please repeatedly check if the polarity and connection sequence are correct
before power up. Wrong connetion would damage the equipments.
Please power off first when pluging or making any connections.
Please using within the range of ESC working current.
Please use welding equipment with full power and choose right-size
welding head. Try to avoid any euipments out of operation or short-circuits
damage caused by wrong welding .
V B AT i s b a t t e r y v o l t a g e , i f c o n n e c t i n g t o o t h e r e q u i p m e n t , p l e a s e m a k e
s u r e i f t h e i n p u t v o l t a g e i s w i t h i n t h e r a n g e .
CRT.(Current) is current detection output interface, which can be connected
to the flight controllers that support current detection like F4 and F7.
For more information, please feel free to contact T-MOTOR after-sale service
center.
Don't add tin wire too much and too fast in welding process in case solder ball
spilling out.
Please carefully check if there are any tin ball or bonded soldering joint before
power up in case equipment damage caused by short-circuit.
Please use 95% or higher purity alcohol or water when cleaning PCB and dont
squeeze components and wires much.
Remedies after water:
Drone
Battery V -
E
S
C
E
S
C
E
S
C
E
S
C
Clean all clutter and dry with hairdryer.
Please dont power on again before making sure there is no water inside any more
Please contact our after-sale service center ASAP.
Stick a layer of electrical tape above cooling fin before welding in case tin or other
pollutes spotting on fin.
Welding Tips:
Please power off at first once ESC
，
FC or other PCBs(including motors) meet
water damage, and dont power on again.
If you can see solder joints or burnt traces on components, which means this
power section has burned out. Please dont power on again then lead to further
damage.
10Pin-10Pin silicone wires in accessories can be connected to T-MOTOR F4 or F7
Flight controller directly
Please make parallel welding for capacitor and power cord positive and negative
(The negative is marked in white on the side of capacitor)
If ESC is matched used with other brands flight controller, please confirm if each
interface definition is correct accordingly. If not, please adjust line sequence at
first, wrong sequence would damge flight controller or ESC.
Thanks for puchasing our Electronics Speed Controller(ESC).
High power system for RC model can be very dangerous.
Any improper use may result In injury and damage to human and
abide by its rules. We assume no responsibilty for personal injury
property damage or consequential losses resulting from the product.
We have a right to modify the design, appearance, performance
and operating requirements of products without notice.
ESC
