background image

 

 

Page - 8 

For more information please email sales@cavidyne.com or call 1-(352)275-5319 

 

 

WARNING

 

 

 

While  the  CaviBlaster

TM

  system  is  very  safe,  operators  should  exercise  care  when  using  the  equipment. 

The cavitation “flame” can be safely passed over the operators’ skin at normal operating distances of 2” - 

3” (5 - 8 cm) from the tip of the nozzle. However, at very close distances (typically less than 1”) both 

nozzles  are  capable  of  causing  harm  to  the  operator, particularly  in  the  initial  instant  that  the  system  is 

activated.  For  that  reason,

  operators  should  exercise  caution  when  operating  the  Zero  Thrust  Gun 

with the nozzles in close proximity to the body. The operators should also ensure that the reverse-

thrust nozzle guard is secured in the correct position prior to operating the Zero Thrust Gun.

 

 

The  operators  of  the  CaviBlaster

TM

  system  should  always  wear  neoprene  or  heavy  rubber  gloves

  to 

provide protection to the hands and, in particular, to the nails. The gloves will absorb most of the energy 

produced by bursting cavitation bubbles and prevent the cavitation bubbles from contacting the operators’ 

hands.  The  gloves  will  also  protect  operators’  hands  from  the  initial  shockwave  when  the  Zero  Thrust 

Gun is activated.

  

 

Serious  harm  and  injury  may  result  from  the  misuse  of  CaviBlaster

TM

  system  equipment  or 

improperly  selected  fittings,  hoses  or  attachments. 

All  components  of  the  system  should  be  checked 

against the  manufacturers’ instructions to ensure that they are compatible with the pressures being used 

and  of  the  correct  thread  type  and  pressure  rating  for  the  intended  service.  Refer  to  these  Operating 

Instructions and to the motor and pressure pump manufacturers’ operation manuals for instructions or call 

CaviDyne, LLC at (352) 275-5319 with any questions. 

 

CAUTION:  

DO  NOT  USE  THIS  EQUIPMENT  TO  CLEAN 
SENSITIVE 

SURFACES 

as 

LED-Lights, 

Underwater Lights, Elecronic Equipment, Etc. 

 

Summary of Contents for Caviblaster 1222-E50









Reviews: