background image

4

Specifications

Power Output

TR:50W+50W (RMS Triode  mode)

UL:80W+80W (RMS

 

Ultralinear  mode)

Frequency Response

8Hz~75kHz (-3dB)

THD

1%(1kHz)

S/N Ratio

92dB

Input Sensitivity

450mV (Integrated)

1300mV (PRE-IN) 

Input Impedance

100k

Ω

Output Impedance

4

Ω

, 8

Ω

Input Terminals 

 LINE1,LINE2,LINE3,PRE-IN

Output Terminals

SUB OUT

WDH

420mm×394mm×200mm

Tube

KT88(EL34)×8

6SN7GTB×1

12AU7EH×2

12BH7EH×2

Net Weight

29.5kg

 

Max Power Consumption

480W

Working Condition

Temperature

0

℃~

40

℃    

Moisture

20%

80%

Storage Condition

Temperature

-20

℃~

70

℃  

Moisture

20%

90%

◆ 

To reduce the risk of electric shock, do not remove the cover.

◆ 

No user serviceable parts inside. Refer servicing to qualified service 

personnel.

◆ 

To reduce the risk of fire or electronic shock, do not expose the unit to 

rain or moisture. 

The  lightning  flash  with  arrowhead  symbol  is  intended  to  alert  user  to  the  presence  of  uninsulated 
“dangerous voltage” within the product's enclosure that may be of a risk shock to persons.

The exclamation point is intended to alert user to the presence of important operation and maintenance
 (servicing) instructions accompanying the appliance.

Summary of Contents for CS-100A


















Reviews: