background image

22

23

TRUE ON LINE UPS

TRUE ON LINE UPS

Problem

Possible cause

Remedy

No indication, no warning tone 
even though system is 
connected to mains power 
supply

No input voltage

Input switch has 
disconnected 
[for 6K(H)/ 10K(H)]

Check building wiring socket outlet  
and input cable.

Set the Input switch to 

ON

LINE LED blinks

Phase and neutral 
conductor at input 
of UPS system are 
reversed

Rotate mains power socket by 180
or connect UPS system according  to
chapter 5 

onnection and operation

.

LINE LED blinks and 
BATTERY-LED lights up

Input power and/or 
frequency are out of 
tolerance

Check input power source and 
inform dealer if necessary

LINE and BYPASS LED light
up even though the power  
supply is available

Inverter not 
switched on

Press On-Switch 

I

INVERTER LED lights up,
and audible alarm sounding
every 1 or 4 seconds

Mains power supply 
has failed

Switching to battery mode automatically.
When audible alarm sounding every
second, battery is almost empty.

INVERTER LED lights up, 
warning tone at intervals of 
every 1 or 4 seconds, mains  
power supply available 
[for 6K/ 10K]

Input switch
disconnected

Set the Input switch to 

ON

. If the 

problem persists, please inform 
your dealer.

FAULT LED lights, warning 
tone once a second

Overload

Remove loads of UPS output.

FAULT-LED lights up, 
permanent warning tone

UPS fault

Notify dealer!!

Emergency supply period 
shorter than nominal value

Batteries not fully 
charged / batteries 
defect

Charge the batteries for at least 
1 - 2 hours and  then check 
capacity. If the problem still 
persists, consult your dealer.

FAULT LED lights, BATTERY-
LED blinks, warning tone once  
a second

Charger or 
Batteries damaged

Notify dealer!!

FAULT LED lights,Indicator3 
and Indicator6 lights, 
permanent warning tone

BATSCR short 
[for 6K/ 10K] 

Notify dealer!!

Please have the following information  at hand before calling the  After-Sales Service 

Department: 

             1. Model number, serial number 

             2. Date on which the problem occurred

             3. Detailed description of the problem

7. Maintenance

7-1 Operation 

The UPS system contains no  user-serviceable parts. If the battery  service life (3~5

years at 25 

 ambient temperature) has been exceeded, the batteries must be replaced. 

In this case please contact your dealer. 

7-2 Storage

If the batteries are stored in temperate climatic zones, they should be  charged every 

three months for 8-10 hours  (see Chapter 5 "Connection and  Operation"). You should 

shorten the charging intervals to two months at locations subject to high temperatures.

Summary of Contents for EA 900RT 10KVAH



















Reviews: