background image

 

VRC2100 Vending Reader 

23 

Installation Guide 

5  CS Gold Settings 

The option to escrow the amount available from the server even if it is 
below the maximum price is provided in the CS Gold Location 
Configuration GUI. If the balance in a patron account is less than the 
maximum price being requested by the reader, the reader will 
automatically take whatever amount is available below the maximum 
price so that lower cost items may be purchased. 

To enable the option: 

1.

 

From the 

CS Gold Menu

, click 

System Configuration

 and then 

click 

Location Configuration

. The 

Location Configuration

 screen 

is displayed. 

2.

 

Select the appropriate VRC2100 location from the 

Locations

 drop-

down list. The parameter information for the VRC2100 is displayed. 

 

3.

 

To allow CS Gold to encumber less than the maximum price, the 
following two parameters must be set to 

1

 

AllowPartialEquivTrans:

 Should Partially Successful Equiv 

Transactions be approved. Set to 

1

 for Yes. 

 

AllowPartialTrans:

 Should Partially Successful Transactions 

be approved. Set to 

1

 for Yes. 

Summary of Contents for VRC2100





























Reviews: