14
Where, NN= last 2 digits of Original Extension numbers that is to be programmed for this feature.
XXXX = Extension number to which call will land in Hotline feature..
Dial #
0000 + 883 # -
To convert all Extensions in “Hot Line to Extension” mode. This also sets hotline landing
extension to Operator.
Dial #
0000 + 884 NN # - To convert NN Extension in normal mode.
Dial #
0000 + 884 # - To convert all Extensions in normal mode. .
Note
:
When all Extensions are converted to Hot Line then to get into the Programming mode, lift Handset
– dial
#
0000
+ whatever Programming to be done.
In Default, if Hot Line to Extension mode is set then all hotline calls will land on operator.
Default: All extension is in Normal Mode.
.
Junction Access During Power Failure
.
When the system is switched OFF, the Junction lines get directly connected to following respective extensions.
Junction Number Extension Number to which it gets connected
01
605
02
606
03
607
04
608
.
Junction Access Codes / Change
.
Junction lines can be accessed in rotation by dialing 0.
To access a particular Junction line, dial #11, #12, #13, #14, #15, #16, #17, #18 (#11 represents the first junction Line and
#18 the last one) from SLT or KTS.
Or one touch junction access using KTS by pressing corresponding CO Key.
.
Junction Access in Circular / Sequential Mode
.
In case of dialing out on the Junction Lines, PBX can be configured to work in either of the following 2 modes:
Mode Description
Circular When an extension dials 0, the PBX will allot Junction numbers 01.
Next time any Extension dial 0, Junction number 02 will be allotted. Then 03 Then 08
…..Then 01.
Sequential When an extension dials 0, the PBX will allot Junction numbers 01.
Next time any Extension dial 0 and if Junction 01 is free then Junction 01 will be allotted. Junction
number 02 will be allotted only when Junction 01 is engaged.
Programming
:
To program in Circular mode, Dial #
0000 + 0620 #
To program in Sequential mode, Dial #
0000 + 0621 #
Default: Circular Mode
.
Junction Access Control
.
Every Extension can be programmed to access one or all of the 4 Junction Lines.
The access to each Extension can be different in Day mode and Night mode.
Procedure
:
Dial #
0000 + 70 J NN X # (For Day Mode access)
Dial #
0000 + 71 J NN X # (For Night Mode access)
Where, J = 1, 2, 3, 4, 5, 6, 7 or 8 representing the 1
st
, 2
nd
, 3
rd
, 4
th
, 5
th
, 6
th
, 7
th
& 8
th
Junction Line.
NN = Last 2 Digits of Extension Number
X = 0 to allow Junction access
1 to Disallow Junction access.
Dial #
0000 + 70 J X # (To allow/disallow all extensions to access “J” Junction in Day Mode)
Dial #
0000 + 71 J X # (To
allow/disallow all extensions to access “J” Junction in Night Mode)
Dial #*0000 + 70 NN X# (To allow/disallow all junction for NN extension in Day Mode)
Dial #*0000 + 71 NN X# (To allow/disallow all junction for NN extension in Night Mode)
Default: All extensions are allowed to access all the 8 Junction Lines in both Day and Night mode.
.
Junction Dialing Controls
.
Junction dialing facility can be controlled Extension wise as below
:
Dial #
0000 + 40 NN L #
where, NN= Last 2 digits of Extension number.
L = 0 -
The Extension can dial only the numbers starting with digits defined in “Allowed Table”
1 - The Extension can dial all numbers.
2 - The Extension can dial all numbers except for ISD numbers.
