18
.
Memory Dialing
.
The PBX has memory for 60 telephone number that can be dialed from an extension by dialing 2digit codes. However if the ext is given
only local dialing facility, then it cannot dial STD number of the memory.
Storing Telephone number in memory
-
Dial #*0000 45 CC J NN#
Where CC is Memory location (01-60)
J is the junction number to be used. (1-8 for specific junction, 0 for available junction in
sequence)
NN is Telephone number maximum 16 digits
Deleting memory codes-
To delete a particular dialing code-
Dial #*0000+ 45 CC#
To delete all memory dialing code-
Dial #*0000+ 46#
Memory Dialing Enable/Disable for extensions with dialing controls-
To Enable
Dial #*0000 + 47 0#
To Disable
Dial #*0000 + 47 1#
Default: Disabled (It will not check Junction dialing control for extension)
To dial a number from memory from SLT Phone-
Dial * 7CC
To dial a number form memory from KTS Phone-
Press
Auto Dial
Key and CC (memory location)
.
Operator Extension Setting
.
In default Extension number 602 is defined as Operator and this extension can be changed if desired by the user.
When Operator extension is busy and another Junction call lands on it, a warning tone is heard by the Operator.
During this time dial FLASH #9.
The 2
nd
Call will get connected & the 1
st
Call will go on Hold.
Now, if required to talk to the first call then dial Flash + #9
To disconnect any of the 2 calls, keep handset down while talking to that Junction line.
Similarly 3
rd
Junction call can also be picked by the Operator by dialing Flash + #9. When 3 Calls are picked by Operator
and put on Hold, then on dialing Flash + #9 the first call on Hold will get retrieved first.
To change the Operator Extension, Dial #
0000 + 15NN#
Where, NN = Last 2 digits of Extension which is to be made the Operator.
Default: Operator Extension is 602
.
Paging (Optional)
.
Connect a PA system to paging port of PBX.
On Dialing
*0
, an extension can broadcast his message through his handset on Paging Port.
.
Password
.
There is only one Password for the whole PBX programming and this Password can be changed by the user. The default
Password is 0000.
Process to change the Password
:
#
0000 + 09xxxx# Here, 0000 = Default password
xxxx = New Password
To reset default Password:
#*#*#*#
.
Redial
.
To redial Telephone number on Junction Line, Dial **
.
Remote Programming
.
The PBX can be programmed by a caller while talking to any of the 4 extensions (601, 602, 603 or 604) through a Junction
Line.
Procedure
:
Caller (Say A) calls on Junction line of the PBX and is talking to Extension 601(Say B).
During communication, B presses FLASH - #0. At this time, if 3 beep tones are received then repeat the process of
FLASH-#0.
Now A dials the 4 digits of the PBX password (Do not dial #
before the PW) & starts doing the required
programming. During B should not hang up. When B hangs up, the call is disconnected.
.
Resetting the PBX programming
.
To reset all the program
of the PBX except Flexible numbering & Junction Enable/Disable to default values,
Dial #
0000 + 0000 + #
To erase only flexible numbering
of the PBX, Dial #
0000 + 9000 + #
.
Ring Time Settings
.
Two type of ringing time can be configured as explained below
:
Junction Ring to be sensed as disconnected
The PBX senses the Junction line as disconnected after 7 secs of the last ring voltage. This time can be reduced or
increased by using the following program:
Dial #
0000 + 182 TT #
Where, TT= 70 in default for 7 secs delay. Reducing this time could give problem in CLI.
