background image

                                                                                                                                                                       

 

           

Operating & Programming Manual 

                          PBX Model: COX-308S / 416S / 432S 

                                    

            

 

We extend a warm welcome to you on becoming a part of the Copper Connections family.  
Our service support Engineers shall be working hard through our channel partners to ensure your satisfaction 
with the product and after sales services.  
We welcome your feedback / query at service@copperconnections.com 

 

.

                                                                   Contents

   

                                                              

.

 

Introduction  
Installation 
Terminologies Used 
Programming the PBX 
Allowed Table 
Auto Call Back  
Auto Call Disconnection 
Auto Attendant Operations     
Auto Attendant Mode settings 
Auto Attendant Message Modes 
Auto Attendant Voice message of 8 Secs 
Auto Attendant Voice message of 20 Secs 
Auto Attendant - Playing a Company message while the call is ringing on an extension 
Barge-In 
Boss Secretary Call 
Call Forward 
Call Pick-Up 
Call Parking 
Checking Extension  PBX Version 
CLI (Calling Line Identification) 
CLI Transferable / Internal CLI 
CLI 

– Digits addition 

CLI Receiving Mode  (DTMF / FSK / Auto) 
CLI Transmitting Mode  (DTMF / FSK)  
Cold Start 
Conference with 1 Junction & 1 Ext 
Conference with 2 Junctions 
Day / Night Mode 
Denied Table 

– A 

Denied Table 

– B 

Do Not Disturb (DND) 
Door Phone 
Door Lock 
Emergency Call 
Extension to Extension call 
Flash Time setting 

Summary of Contents for COX-308S


















Reviews:

Related manuals for COX-308S