V5SR
500 Kg Surface Mount Electromagnetic lock
EN
G0301FR1025V03
All the information contained within this document (photos, drawing, features, specifi cations and dimensions) could be perceptibly different and can be changed without prior notice.
PRODUCT PRESENTATION
Monitored
Surface mount
High Corrosion resistance
Safety Rope
Delivered with armature
No mechanical wear
Ease of installation
Recommended for interior use
Fail safe (Door unlocked when power off)
Holding force: 500 kg
No residual magnetism
Visual signalling (Blue = Locked ; Green = Open)
Built-in varistor: Built-in electronic protection
to eliminate back EMF
Dimensions (L x W x D): 272 x 66 x 40 mm
Armature dimensions (L x W x D): 185 x 60 x 12mm
Power supply: 12/24V dc
Power absorption: 12 V DC = 550mA
24 V DC = 275mA
PACKAGE CONTENTS
Magnetic lock
Armature
plate
Fixing plate
Security rope
Roll pin 5x16
4X10 screw
4x25 screw
1
1
1
2
2
1
6
Steel washer
Rubber
washer
M8x35 screw
M8x25 screw
Cap nut
Manual
2
1
1
1
1
1
ELECTRICAL CONNECTIONS
MOUNTING RECOMMENDATIONS
Armature plate
- It is vital to fi x the electromagnetic lock and
armature plate solidly on their supports.
- Make sure that the magnet and the armature
meet evenly over their entire mating surfaces.
- The armature plate must be able to pivot slightly
about its center mounting screw to compensate
for any door misalignment.
Security rope
(fi xing on the magnetic lock and the frame)
Security ropes
The electromagnetic lock undergoes repeated
shocks and the vibration at the points of fi xation
on the frame (frequencies of openings / closures,
attempt of opening wears closed and attempts
of vandalism) which can loosen the fi xing bolts/
screws.
To prevent the risk of the electromagnetic block
from falling, install both security ropes supplied,
to guarantee the safety of the users (see plan
above).
Voltage selection jumpers
Recommended power supplies
12V dc default setup
The N.O./N.C. signal only switches when the door
is closed and the electromagnetique lock powered.
The V5SR is suitable for the new
regulations covering assistance to
persons with reduced mobility.
Check the jumper position before connecting the
lock to the input current. A wrong position could
damage the lock. This type of damage is not
covered by the warranty.
IMPORTANT NOTE
Terminal
block
Correspondence
+
12 or 24V dc
-
- 0 V
NO
Normally open
C
COM
NC
Normally closed
ADC335
12V dc
ADC612SB
24V dc
EC certifi cation
WEEE & RoHS
IP42
INSTALLATION
Fixing plate
Security rope
M8 screw
Roll pin
Armature plate
Steel washer
Rubber washer
Cap nut
1,6
2 max.
15,6
3
2
2,9
5,3
2,5
12 round chips 2mm
for the tester pins
37
43
18,10
3,9
3,9
9
5,6
3,05
2,9
18,45
6,81
Specifications :
- Epoxy 1,6mm
- Class 4
- PCBoard with 4 layers
- Metallized holes
- Cooper 35µm for all layers
- Chemical finishing Nickel/Gold
(Nickel 5µm ; Gold 0,05 µm)
- Green solder mask on the 2 sides
- Mounting in panel with trimming,
and 4 technical stripes of 7mm around the panel
- 2 sights
Comply with the standards RoHS
Ce document est la propritété exclusive de CDVI, il ne peut être communiqué à des tiers sans son autorisation.
This document is the exclusive property of CDVI and it may not be disclosed to others without permission.
31, av du Gal Leclerc
93691 PANTIN CEDEX
F R A N C E
Tel : 33(0)148910102
Fax : 33(0)148912121
www.cdvi.com
Plan M2653
Edition 02-V2
Date 10/01/2018
SCALE 1:1
A4V
DWG.: A. Broustal
Material : epoxy
General Tol.: class 4
Surface condition: ...
C.A. :
C3504QFD867
PCB D867 (V3SR_V5SR)
epoxy 1,6mm - copper 35µm
Project : ...
Vol. (mm
3
) :
Weight (g) :
Security rope
(For general use - not fi re safety use)
10
WARRANTY
YEAR
