COOLMARKET UF 380 INOX
65
64
ENGLISH
ENGLISH
- Do not use bristle brushes, steel wire brushes, detergent, soap powder, alkaline detergent,
benzine, petrol, acid, hot water or other corrosive elements to clean the freezer surface,
door gasket, plastic decorative parts, etc., to avoid damage.
- Carefully dry the door gasket and clean the slot with a wooden stick wrapped with cotton.
After cleaning, fix the four corners of the door gasket and then gradually push it into the
slot in the door.
Power failure or cooling system fault
If you receive an early power failure warning:
- Activate the fast freeze function, so that food is completely frozen. Set the temperature
back to the original setting when the power supply returns to normal.
Note:
It is advisable to run the freezer uninterruptedly once you start using it.
Defrost
This freezer includes an automatic defrost function, so there is no need to defrost it manually.
Light bulb substitution
The freezer has a LED light with low consumption and a long shelf life. In case of malfunction,
contact the official Technical Support Service of Cecotec. The light bulb can only be substituted
by the manufacturer.
Note:
If the power cord and/or plug are damaged or dusty, electric shock and fire may occur. If there
is any malfunction, disconnect the cord and contact the Technical Support Service of Cecotec.
7. TROUBLESHOOTING
For the following minor malfunctions, please try to solve the problem yourself before
contacting Cecotec Technical Support Service.
Problem
Possible causes
Possible solutions
The freezer
does not work.
The freezer is not connected to the
mains.
The circuit breakers or fuses are
damaged.
There is no power or the fuse trips.
Connect the freezer to a power
supply.
Open the door and check the light
is on.
Abnormal
noise
The freezer is not stable.
The freezer is in contact with the
wall.
Adjust the levelling feet.
Remove the freezer from the wall.
Low cooling
efficiency
The food introduced is hot or there
is too much food.
You open the door too often.
The door gasket has objects that do
not allow to close it completely.
The freezer receives direct sunlight
or is close to a heat source.
The freezer is not well ventilated.
The selected temperature is too
high.
Introduce food in the freezer when it
is at room temperature.
Check and close the door.
Remove the freezer from the heat
source.
Keep the recommended distances
in the installation section so the
freezer is well ventilated.
Adjust a suitable temperature.
Undesired
odours in the
freezer.
There is spoiled food inside.
The freezer is dirty.
You introduced food with strong
smells.
Dispose of food which is spoiled.
Clean the freezer.
Pack food, especially if it has a
strong smell.
The buttons do
not work
Check if the child lock is active.
Hold down the Unlock button for 3
seconds to deactivate the child lock
and press any button. (To get more
information, read the instructions on
the child lock).
You cannot
set the
temperature.
Check that the fast cooling or freeze
functions are not active on the
control panel.
Deactivate the special functions and
then set the temperature (for more
details, check the Operation section).
The
temperature
on the freezer
compartment
is shown on
the panel, but
it flashes.
Check that the power supply has not
been cut off before.
Press any button to activate the
alarm (check the overheating
warning section) and check that
the food inside the freezer is not
spoiled.
Note:
If none of these situations match your problem, do not attempt to disassemble or repair the
freezer yourself. Repairs carried out by unqualified persons may result in injury or serious
malfunctions. Please contact the place where you bought the appliance or the Cecotec
Technical Support Service. The repair must be carried out by an authorised technician and you
must use only original spare parts.
Error codes
Error type
E0 (while the freezer compartment icon is lit
up)
Fault of the temperature sensor
