background image

CAUTION: 

 

The  CEIL  DSP  Sine  wave  Static  UPS  should  be  connected  to  grounded,  permanent  wiring 

systems. 

Personal Precautions: 

 

A person should be within the range of your voice so as to come to your aid when you 

work near batteries 

 

Keep  plenty  of  fresh  water  and  soap  nearby  in  the  event  that  battery  acid  comes  in 

contact with skin, clothing or eyes. 

 

Avoid touching eyes while working near batteries; Wash your hands when work done. 

 

If battery acid comes in contact with skin or clothing wash immediately with soap and 

water. If acid enters eyes immediately flood eyes with running cool water for at least 15 

minutes and get medical attention immediately. 

 

Baking soda neutralizes battery electrolyte. 

 

NEVER smoke or allow spark or a flame in the vicinity of the battery. 

 

Be  extra  cautious  when  working  with  metal  tools  on  and  around  batteries.  It  could 

short-circuit  the  batteries  or  other  electrical  parts,  producing  a  spark  that  could  cause 

an explosion. 

 

Remove  personal  metal  items  such  as  rings,  bracelets,  necklace  and  watches  when 

working  with  the  battery.  Battery  can  produce  short-circuit  current  high  enough  to 

cause severe burns. 

 

Never attempt to charge a frozen battery. 

 

Before touching the Battery terminal makes sure that the Static UPS front switch is OFF 

and AC mains to the Static UPS is also OFF. 

 

If it is necessary to remove any battery, always remove the grounded terminal from the 

battery first. Make sure all the accessories are off, so as not to cause arcing. 

 

Be sure that the area around the battery is well ventilated. 

 

Clean battery terminals. Be careful not to allow corrosion to come in contact with eyes. 

 

Study  specific  precautions  and  recommended  rates  of  charge  of  all  battery 

manufacturers. 

 

Add only distilled water in each cell until battery acid reaches level specified by battery 

manufacturer.  This  helps  purge  excessive  gas  from  cells.  Do  not  overfill.  For  a  battery 

without caps, carefully follow manufacturer's recharging instructions. 

Exide India, is not responsible for any kind of battery related problems. 

 

Summary of Contents for Static UPS System




















Reviews: