background image

4.5. PROBLEMS

Problem

Solutions

PWR LED is not lights.

Check polarization and parameters of connected power supply.

Rx LED lights continuously

RS485(4W) /RS422 bus. Wrong polarization on  Rx+, Rx- terminals. Change polarization.

RS485(2W) bus. Wrong polarization on Tx+/A, Tx-/B terminals. Change polarization.

No transmission,

Tx LED is  blinking

RS485(4W) /RS422 bus. Check the correctness of connection to  Tx, Rx terminals according

to chapter 3.

RS485(2W) bus. Check the correctness of configuration setting according to chapter  4.

5. RS232 INTERFACE – PIN DESCRIPTION OF  DSUB-9F-DCE SOCKET

Pin

Signal

Description

ADA-1040

1 (DCD)

Level of receiver signal

Connected with DSR

2 (TxD) 

Data transmission via ADA-1040

Transmitter

3 (RxD) 

Data receiving via ADA-1040

Receiver

4 (DSR) 

Readiness of receiving via ADA-1040

Receiver (in ADA-1040-x-2-x-x)

Connected with DTR (in ADA-1040-x-1-x-x)

5 (SG) 

Signal ground

GND

6 (DTR) 

Readiness of data receiving/ transmission from ADAI1040

Receiver (in ADA-1040-x-2-x-x)

Connected with DSR (in ADA-1040-x-1-x-x)

7 (CTS) 

Readiness of  transmission to ADA-1040

Connected with RTS

8 (RTS)

  Demand of transmission from  ADA-1040

Connected with CTS

9 (RI)

Call rate

Connected with 

+5VDC

 of converter's in versions:

ADA-1040-x-19-x-x, 

ADA-1040-x-29-x-x.

Not connected in other versions.

6. VERSIONS

ADA-1040 - 

-

-

-

Order example:
Product Symbol: 

ADA-1040-1-1-23-3

1

 – basic version of electronic,

1

 – TX, RX signals

23

 - galvanic isolation 1kV=, 3-way

3

 - cover without inlets, plug-in screw 

terminal block,

Electronic versions:

Basic,

1

Special,

2

Signals:

TX, RX 

1

TX, RX . +5VDC on 9 pin of RS232 DB-9F connector

19

TX, RX, DTR, DSR – only in version 2-way isolation

2

TX, RX, DTR, DSR +5VDC on 9 pin of RS232 DB-9F connector

– only in version 2-way isolation

29

Galvanic isolation:

1kV= 2-way

2

1kV= 3-way

23

3kV= 2-way

3

3kV= 3-way

33

Terminal & Terminal Cover:

Cover without inlets, screw terminal block

1

Cover with inlets, screw terminal block

2

Cover without inlets, plug-in screw terminal block

3

10

ADA-1040

Summary of Contents for ADA-1040













Reviews: