background image

8. VERSIONS

ADA-1040D - 

-

Order example:
Product Symbol: 

ADA-1040D-23-3

23

 - galvanic isolation: 1kV= 3-way,

3

 - cover without inlets, plug-in screw terminal block

Galvanic isolation:

1kV= 2-way

2

1kV= 3-way

23

3kV= 2-way

3

3kV= 3-way

33

Terminal & Terminal Cover:

Cover without inlets, screw terminal block

1

Cover with inlets, screw terminal block

2

Cover without inlets, plug-in screw terminal block

3

9. SPECIFICATION

TECHNICAL DATA

Transmission Parameters

Interface

RS-232

RS-485/RS-422

Connector

DSUB-9 Female

Screw terminal block - max. Ø 2,5mm

2

Max. Line length

15 m

1200 m

Max. number of connected device

1

1

Transmission line

DB9F/DB9M multicore cable  9x0,34 
shielded or  9-pair twisted cable, UTP 
9x2x0,5 (24AWG) shield inside large 
interferences STP 9x2x0,5 (24AWG).

1-pair or 2-pair twisted cable, UTP 
Nx2x0,5 (24AWG), shield inside large 
interferences STP Nx2x0,5 (24AWG)

Standards

EIA-232, CCITT V.24

EIA-485, CCITT V.11

Max. baud rate

230,4 kbps

Transmission type

Asynchronous full duplex, half duplex.

Optical Signalization

PWD – green LED power supply,

RX - red LED data receiving on RS485/RS422,

TX - yellow LED data transmission via RS485/RS422.

Electrical Parameters

Power requirements

10 - 24 – 30 V DC

Power Cable

Recommended length of power cable – up to 3m

Power

<2W

Protection from reverse power polarization

YES

Galvanic Isolation

1kVDC or 3kVDC - between power circuit and RS-232 signal line

Optoisolation 

3kV - between signals lines RS-232 and RS-485 

Electromagnetic compatibility

Resistance to disruptions according to the standard PN-EN 55024.
Emission of disruptions according to the standard PN-EN 55022.

Safety requiring

According to the PN-EN60950 norm.

Environment

Commercial and light industrial.

Environmental Parameters

Ambient temperature

-30 ÷ 60°C

Relative air humidity

5 ÷ 95% - non-condensing

External Storage Temperature

 -40 ÷ +70°C

Casing

Dimensions

53 x 90 x 62 mm

Material

PC/ABS

Degree of casing protection

IP40

Degree of terminal protection

IP20

Weight

0,10 kg

13

ADA-1040D

Summary of Contents for ADA-1040D

















Reviews: