1. GENERAL INFORMATION
Thank you for your purchase of
CEL-MAR
Company product. This product has been completely tested and is covered by a two year
warranty on parts and operation from date of sale.
If any questions or problems arise during installation or use of this product, please do not hesitate to contact Technical Support at +48
41 362-12-46 or e-mail support@cel-mar.pl.
1.1. GUARANTEE INFORMATION
ADA-4010A converter
is covered by a two year warranty from date of sale. In case of being damaged it will be repair or the damaged
component will be replace. The warranty does not cover damage caused from improper use, materials consumption or any
unauthorized changes. If the product does not function (is damaged), or not operate in accordance with the instructions, will be
repaired or replaced.
All warranty and no warranty repairs must be returned with paid transport and insuring to
CEL-MAR Company.
CEL-MAR Company
under no circumstances won't be responsible for ensuing damage from improper using the product or as a result
of random causes: the lightning discharge, the flood, the fire and the like.
CEL-MAR Company
is not be held responsible for damages and loss including: loss of profits, loss of data, pecuniary losses ensuing
from using or the impossibility of using this product.
In specific cases
CEL-MAR Company
discontinue all warranties and in particular do not follow the user manual and do not accept
terms of warranty by the user.
1.2. GENERAL CONDITIONS FOR SAFE USE
The device should install in the safe and stable place (e.g. switchbox unit), the powering cable should be arranged this way isn't
exposed to treading, catching or tear out from power circuit.
Do not put device on the wet surface.
Do not connect devices for nondescript powering sources,
Do not damage or crush powering wires.
Do not make connection with wet hands.
Do not adapt, open or make holes in casings of the device!
Do not immerse device in water or no other liquid.
Do not put the fire opened on device sources: candles, an oil lamps and the like.
Complete leaving out of the powering network is coming only after disconnecting voltage in the powering circuit.
Do not take the installation or device disassembly if it is turn on. It can lead to the electric short circuit and damaging the device.
The device can not be used for applications that determine human life and health (eg. Medical).
1.3. CE LABEL
The CE symbol on the device CEL-MAR means compatibility with electromagnetic compatibility Electromagnetic
Compatibility Directive
EMC 2014/30/WE.
Declaration of Conformity is available by contact with Technical Service
(email: support@cel-mar.pl; phone: +48 41 362-12-46).
1.4. ENVIRONMENTAL PRESERVATION
This sign on the device inform about putting expended device with other waste materials. Device should send to the
recycling. (In accordance with the act about the Electronic Appliance Expended from day 29 of July 2005)
1.5. SERVICE AND CONSERVATION
The ADA-4010A converter doesn't require the periodic conservation.
Technical support at the number: +48 41 362-12-46 in 8.00-16.00, from Monday to Friday.
1.6. PACK CONTENTS
The converter is delivered with the user manual, resistors: Rt=120
W
(2 pcs.), CD with ADAConfig software.
2. PRODUCT INFORMATION
2.1. PROPERTIES
●
Possibility for adding the address to not addressable device connected to RS232 interface,
●
Conversion data format and baud rate on RS485 / RS422 and RS232 converter ports,
●
Operating on 2 or 4 wire bus in point-to-point or multi-point mode,
●
Conversion of TX, RX signals to RS485/RS422 standard,
●
RTS data flow control via RS232 port,
●
Operating up to 32 devices on RS485 network,
●
Baud rate of RS232 and RS485/422 interfaces (bps): 300, 600, 1200, 1800, 2400, 4800, 7200, 9600, 14400, 19200, 28800,
38400, 57600, 76800, 115200, 230400,
●
RS232 & RS485/422 interface's data format: Number of data bites: 5, 6, 7, 8; Parity: None, Odd, Even; Number of stop bits : 1, 2,
●
Transparent for all protocols which data format is in accordance with the above specifications of RS485/422 interfaces e.g.
MODBUS, DNP, PROFIBUS and others,
●
Power supply 10 - 30 VDC stable min. 2W,
●
5kV= optoisolation in signal channel between RS232 and RS485/RS422 interface,
●
1kV= or 3kV= galvanic isolation between RS485/RS422 interface and power supply,
●
Connection RS485/RS422 and RS232 buses and power supply via screw terminal block 2.5 mm
2
,
●
Implemented short circuit protection and over-voltage protection on RS-485/RS-422 interface's lines,
●
Protection against power supply reverse connection,
3
ADA-4010A
Summary of Contents for ADA-4010A
Page 15: ...15 ADA 4010A...
