background image

2.4. ISOLATION 

ADA-4040PC8 converter has 3-way galvanic isolation on the levels 1kV= or 3kV=, depend on version described in section 

VERSIONS

.

Fig 2. Isolation structure 

3. INSTALLATION 

This chapter will show how to use and connect ADA-4040PC8 to JCT controllers (VIRAP* company with RS485 interface); to RS485 / 

RS422 bus and power supply

In the purpose of minimization of disruptions from environment is being recommended to:

- apply multipair type shielded cables, which shield can be connected to the earthing on one end of the cable,

- arrange signal cables in the distance not shorter than 25 cm from powering cables.

- apply cable of adequate cross-section due to voltage drops for converter powering,

- use suppression filters for powering converters that are installed within a single object.

- not supply converter from power circuit device that generates large impulse interference such as transmitters, contactors.

3.1. ASSEMBLING 

Casing of ADA-4040PC8 is adapted it assembly he TS-35 (DIN35) rail. It install the converter, should ugh mounted he the rail upper

part of the cover then press bottom part it hear characteristic "Click" sound. 

3.2. COMPUTER CONNECTION 

To connect ADA-4040PC8 to computer, is needed additional converter e.g. ADA-I9141 USB to RS485/RS422 converter; connected to 

JCT port (5-pins connector) of ADA-4040PC8.

Typical connections of ADA- 4040PC8 to PC are shown bellow. 

 Fig 3. 4-Wires connection of ADA-4040PC8 to PC by the use of ADA-I9141 USB to RS485/RS422 converter.

Fig 4. 2-Wires connection of ADA-4040PC8 to PC by the use of ADA-I9141 USB to RS485/RS422 converter.

3.3. RS485 NETWORK CONNECTION 

RS485/RS422 interface in ADA-4040PC8 converter is available on terminal block, described as: Tx+/A, Tx-/B, Rx+, Rx-. Connection of

ADA-4040PC8 to RS485(4W) and RS485(2W) network are shown bellow.

5

ADA-4040PC8 

POWER

10 - 30VDC

JCT-ASCII

RS485

MODBUS-RTU

RS485/RS422

3-WAY ISOLATION

GND

USB

USB

connector

RS485 / RS422

connector

USB

connector

ADA-I9141

USB

Rx+

Rx-

Tx+/ A

Tx-/ B

Tx+ / A

Tx- / B

   

Rx+

Rx-

RTU

RS485 / RS422

connector

Tx+ / A

Tx- / B

GND

Rx+

Rx-

JCT

RS485 / RS422

connector

GND

PC

ADA-4040PC8

GND

USB

PC

USB

Rx+

Rx-

Tx+/ A

Tx-/ B

Tx+ / A

Tx- / B

   

Rx+

Rx-

Tx+ / A

Tx- / B

GND

Rx+

Rx-

GND

ADA-I9141

ADA-4040PC8

USB

connector

RS485 / RS422

connector

USB

connector

RTU

RS485 / RS422

connector

JCT

RS485 / RS422

connector

Summary of Contents for ADA-4040PC8


















Reviews: