background image

 

25 

V3.15.22

 

 
 

24. 

Plug in the Condensing Unit.  The Condensing Unit should turn on for a brief 
period, and then shut off.   

25. 

Plug in the Evaporator.  The controller should light up.  Turn the controller 
on so that a temperature value is displayed.  There is a 3 minute delay at 
start  up  indicated  by  a  blinking  snowflake  icon  on  the  display.    After  3 
minutes, a snowflake and fan icon should appear on the display, lit solid.  
The system is now in cooling mode.  Verify that the Condensing Unit has 
turned on, and that the Evaporator is producing cold air. 

 

 
Installation Tips and Guidelines  

 

  Make  sure  you  attach  the  line  set  hoses  in  the  sequence  described  in  the 

instructions 

  Make sure to plug in power cords in the sequence described in the instructions 

  Before attaching each connection, STOP and double-check that BLUE and RED 

female  connections  are  attached  to  corresponding  BLUE  and  RED  male 
connections  

  Inspect Evaporator and Condensing unit fans to confirm airflow.  There shouldn’t 

be any excessive vibration, noise or obstructions to airflow. 

  Do  not  leave  the  system  unattended  until  it  has  reached  normal  operating 

conditions,  and  the  system  has  been  observed  properly  cycling  on/off  to  the 
desired set point and differential. 

 

 

 

 

Summary 

Keep in mind the following guidelines before purchasing a wine cooling unit from 
CellarPro: 

  If  the  cellar  is  too  large  for  the  cooling  unit,  the  cooling  unit  will  be  unable  to 

maintain proper, even temperatures inside the cellar. 

  Without proper insulation and an airtight environment, the cooling unit effectively will 

become a de-humidifier and potentially will produce buckets of water. 

  If the condensing unit does not have access to cool air, either because of 

improper ventilation or because the environments is too hot, the cooling unit will 
be unable to maintain proper temperatures inside the cellar. 

Under  any  of  the  above  conditions,  the  unit’s  internal  components  may  become 
damaged,  the  expected  useful  life  of  the  wine  cooling  unit  may  be  adversely 
affected, and the product’s warranty may become null and void. 

 

 

 

Summary of Contents for 3000Shqc-EC







































Reviews: