background image

 

CelloTrack T Installation Guide 

 

 

 

CelloTrack T Installation Guide

                                                                               

 Page 2 of 20  

Copyright © 2014 by Pointer Telocation, Ltd. 

 

Legal Notices 

 

IMPORTANT 

1.  All legal terms and safety and operating instructions should be read thoroughly before 
the product accompanying this document is installed and operated. 

2.  This document should be retained for future reference. 

3.  Attachments, accessories or peripheral devices not supplied or recommended in 
writing by Pointer Telocation Ltd. May be hazardous and/or may cause damage to the 
product and should not, in any circumstances, be used or combined with the product. 

General  

The product accompanying this document is not designated for and should not be used in 
life support appliances, devices, machines or other systems of any sort where any 
malfunction of the product can reasonably be expected to result in injury or death.  
Customers of Pointer Telocation Ltd. using, integrating, and/or selling the product for use 
in such applications do so at their own risk and agree to fully indemnify Pointer Telocation 
Ltd. for any resulting loss or damages.

  

Warranty Exceptions and Disclaimers 

Pointer Telocation Ltd. Shall bear no responsibility and shall have no obligation under the 
foregoing limited warranty for any damages resulting from normal wear and tear, the cost 
of obtaining substitute products, or any defect that is (i) discovered by purchaser during 
the warranty period but purchaser does not notify Pointer Telocation Ltd. Until after the 
end of the warranty period, (ii) caused by any accident, force majeure, misuse, abuse, 
handling or testing, improper installation or unauthorized repair or modification of the 
product, (iii) caused by use of any software not supplied by Pointer Telocation Ltd., or by 
use of the product other than in accordance with its documentation, or (iv) the result of 
electrostatic discharge, electrical surge, fire, flood or similar causes.  Unless otherwise 
provided in a written agreement between the purchaser and Pointer Telocation Ltd., the 
purchaser shall be solely responsible for the proper configuration, testing and verification 
of the product prior to deployment in the field. 

POINTER TELOCATION LTD.’S SOLE RESPONSIBILITY AND PURCHASER’S SOLE REMEDY 
UNDER THIS LIMITED WARRANTY SHALL BE TO REPAIR OR REPLACE THE PRODUCT 
HARDWARE, SOFTWARE OR SOFTWARE MEDIA (OR IF REPAIR OR REPLACEMENT IS NOT 
POSSIBLE, OBTAIN A REFUND OF THE PURCHASE PRICE) AS PROVIDED ABOVE.  
POINTER TELOCATION LTD. EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES OF ANY 
KIND, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED 
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, SATISFACTORY 
PERFORMANCE AND FITNESS FOR A PARTICULAR PURPOSE.  IN NO EVENT SHALL 
POINTER TELOCATION LTD. BE LIABLE FOR ANY INDIRECT, SPECIAL, EXEMPLARY, 
INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING WITHOUT LIMITATION LOSS 
OR INTERRUPTION OF USE, DATA, REVENUES OR PROFITS) RESULTING FROM A BREACH 
OF THIS WARRANTY OR BASED ON ANY OTHER LEGAL THEORY, EVEN IF POINTER 
TELOCATION LTD. HAS BEEN ADVISED OF THE POSSIBILITY OR LIKELIHOOD OF SUCH 
DAMAGES.  

Summary of Contents for CelloTrack T





















Reviews: