background image

RECOMMENDED PARAMETERS FOR PROTEIN HYDROLYSIS

Power =  

150 W

Power Mode =  

STANDARD

Temperature =  

150° C

Temperature Control = 

Fiber-optic

Pressure= 

100 psi

Run Time = 

2:30

Hold Time = 

15:00

PARTS AND ACCESSORIES

SYSTEM

PRODUCT NAME

PART #

Discover Protein Hydrolysis

    (100-120V/50-60Hz)

925480

 

Includes the Following:

 

  Bioscience Discover (100-120V/50-60Hz)

908005

 

  Discover Protein Hydrolysis Option

925590

 

  Vacuum Pump (100-120V/50-60Hz)

544530

 

  Fiber-Optic Temperature Control

541175

Discover Protein Hydrolysis

    (200-240V/50-60Hz)

925482

 

Includes the Following:

 

  Bioscience Discover (200-240V/50-60Hz)

908010

 

  Discover Protein Hydrolysis Option

925590

 

  Vacuum Pump (200-240V/50-60Hz)

544540

 

  Fiber-Optic Temperature Control

541175

ACCESSORIES

PRODUCT NAME

PART #

Complete Valve Panel Assembly

908275

Reaction Vessel Top with 2 Ports

148460

Reaction Vessel Bottom

324015

Microvial Tray Insert

324020-P

Condensation Shield

324030

Fiber-Optic Temperature Probe

314325

Thermowell Assembly (Qty 2)

430676

Discover Protein Hydrolysis Operations Manual

600313

Wrench Set

SP-1367

Summary of Contents for Discover Protein Hydrolysis







Reviews: