manualshive.com logo in svg

Centaur 2008 Centaur, Operator'S Manual

The Centaur 2008 Centaur is a versatile and powerful machine designed for various applications. To get the most out of this exceptional product, make sure you have the Operator's Manual on hand. Download the manual effortlessly and free of charge from our website, ensuring optimal performance and safe operation.

Share
Download
background image

TABLE OF CONTENTS

SECTION                                                                                                                                                                            PAGE

V

 

 

 

 

To adjust the brake caliper .............................................................................................. 22

 

 

7.3.3   BRAKE PAD REPLACEMENT 

 ................................................................................................. 22

 

 

7.3.4   BRAKE CABLE ADJUSTMENT

 ................................................................................................ 23

 

 

 

 

To adjust the brake cable ................................................................................................ 23

 

7.4   HYDRAULIC BRAKE 

 ............................................................................................................................... 23

 

 

7.4.1  

 

GENERAL  .......................................................................................................................... 23

 

 

7.4.2  

BRAKE FLUID LEVEL 

 ............................................................................................................. 23

 

 

7.4.3  

 

CHANGING BRAKE FLUID 

 ............................................................................................ 24

 

 

7.4.4  

 

HYDRAULIC BRAKE PAD INSPECTION

 ....................................................................... 24

 

 

 

 

 

Brake Pad Inspection Procedure  ......................................................................................... 24

 

 

 

 

 

To replace the brake pads  .................................................................................................... 24

 

 

7.4.5  

 

ENGINE COOLING & EXHAUST SYSTEM ................................................................... 24

 

7.5   STEERING SYSTEM  ................................................................................................................................. 25

 

 

7.5.1  

 

STEERING CENTERING ADJUSTMENT 

 ....................................................................... 25

 

 

7.5.2  

 

STEERING WHEEL & LOCK ADJUSTMENT 

 ................................................................ 25

 

 

7.5.3  

 

HYDROSTATIC TRANSMISSION DRIVE BELT ............................................................ 26

 

7.6   SHIFTING SYSTEM.................................................................................................................................... 26

 

 

7.6.1  

 

SHIFT CABLE ADJUSTMENT 

 ......................................................................................... 26

 

 

7.6.2  

 

THROTTLE CABLE ADJUSTMENT

 ................................................................................ 26

 

7.7 

MAINTENANCE SCHEDULE ................................................................................................................... 27

8.0  

TROUBLESHOOTING

  ........................................................................................................................................ 28

9.0  

CLEANING AND STORAGE

 

9.1   CLEANING THE VEHICLE  ...................................................................................................................... 30

 

9.2   STORING THE VEHICLE .......................................................................................................................... 30

 

 

 

Clean the Vehicle  ................................................................................................................................ 30

 

 

 

Drain the Fuel System  ......................................................................................................................... 30

 

 

 

Prepare the Battery for Storage  ........................................................................................................... 30

 

 

 

Protect the Electrical System  .............................................................................................................. 30

 

 

 

Raise the Vehicle .................................................................................................................................. 30

 

 

 

Preparing the Engine for Storage  ........................................................................................................ 30

10.0 

POTENTIAL HAZARDS

   ..................................................................................................................................... 31

11.0 

ACCESSORY INFORMATION 

 

11.1   GENERAL .................................................................................................................................................... 35

 

11.2   REAR CARGO TIE DOWN BARS (Part No. 849-116)

 .............................................................................. 35

 

11.3   ALL SEASON TRACK KIT (Part No. 849-150)

 ......................................................................................... 35

 

 

11.3.1   Track Installation .......................................................................................................................... 35

 

 

11.3.2   Operating Precautions ................................................................................................................... 36

 

11.4  WINTER TRACK KIT (Part No.849-160)

 ................................................................................................... 37

 

 

11.4.1 

Installing the Axle Extension

 ........................................................................................................ 37

 

 

11.4.2 

Track Installation .......................................................................................................................... 37

 

 

11.4.3 

Removal of Tracks ........................................................................................................................ 38

 

 

11.4.4 

Operating Precautions ................................................................................................................... 38

 

11.5  ICE CLEAT KIT (Part No. 848-130)

 ............................................................................................................ 38

 

11.6   WINCH KIT (Part No. 849-114)

 .................................................................................................................. 39

 

 

11.6.1 

Rules For Safe Operation .............................................................................................................. 39

 

 

11.6.2   Tips for Extending the Life of Your Winch

 .................................................................................. 40

 

11.7   RECEIVER WINCH KIT (Part No. 849-123)

 .............................................................................................. 41

Summary of Contents for 2008 Centaur

























































Reviews:

No comments

Related manuals for 2008 Centaur

Panasonic NS1000 Quick Reference Manual preview
NS1000
Brand: Panasonic Pages: 2
Yamaha VK10L Owner'S Manual preview
VK10L
Brand: Yamaha Pages: 98
Yamaha YFM660FS Owner'S Manual preview
YFM660FS
Brand: Yamaha Pages: 191
Bad Boy Onslaught 550 EFI 4X4 EPS Owner'S Manual preview
Onslaught 550 EFI 4X4 EPS
Brand: Bad Boy Pages: 67
Hammerhead 2013 R 150 Owner'S Manual preview
2013 R 150
Brand: Hammerhead Pages: 100
GMX MOTORBIKES GMX 125 SPORTZILLA X User Manual preview
GMX 125 SPORTZILLA X
Brand: GMX MOTORBIKES Pages: 28
Canyon 250 Owner'S Manual preview
250
Brand: Canyon Pages: 83
Can-Am Rally 200 Operator'S Manual preview
Rally 200
Brand: Can-Am Pages: 140
PRONAR T680 Operator'S Manual preview
T680
Brand: PRONAR Pages: 147
Polaris 2014 RZR XP 1000 Service Manual preview
2014 RZR XP 1000
Brand: Polaris Pages: 474
Yamaha YFM700RV 2009 Service Manual preview
YFM700RV 2009
Brand: Yamaha Pages: 409
BRP Can-Am DS 450 EFI 2009 Predelivery Bulletin preview
Can-Am DS 450 EFI 2009
Brand: BRP Pages: 19
Westbrook Trailers 48-048-K08 Assembly Instructions Manual preview
48-048-K08
Brand: Westbrook Trailers Pages: 34
Thomas PROTOUGH 900 Owner/Operator And Parts Manual preview
PROTOUGH 900
Brand: Thomas Pages: 165
ShoreLand'r 69175 Series Service Manual preview
69175 Series
Brand: ShoreLand'r Pages: 2
ShoreLand'r SLB46TBLSP Service Manual preview
SLB46TBLSP
Brand: ShoreLand'r Pages: 10
Peg-Perego CORRAL T-REX 2011 Use And Care Manual preview
CORRAL T-REX 2011
Brand: Peg-Perego Pages: 36
Claas LEXION 410 Operator'S Manual preview
LEXION 410
Brand: Claas Pages: 41

Brands by name

Popular brands

Load more brands