background image

PRODUCT SPECIFICATIONS

Item  D escription 

Electric  M otor 

2 H P ,  110 V , 60 H z, Single Phase, 1150 W atts 

P ow er  C ord 

14 A W G   x 3C ,  D ouble  Insulated   

M easured Am perage 

8.1 w ith no load 
10 w ith load 
30 at start-up 

M axim um  Force 

4 Tons (8,000 Lbs.) 

Log S ize C apacity 

20” L x 10” D  

W edge Size 

5” 

R am  Travel 

14-1/2” 

R am  D iam eter 

1.75” 

H ydraulic  O il C apacity 

3.2 Q uarts 

O verall D im ensions 

30-1/2” L x 12” W   x  19-1/4”  H  

W eight 97 

Lbs. 

 

SAVE THIS  MANUAL

You will need this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures, parts list and assembly diagram.
Keep your invoice with this manual.  Write the invoice number on the inside of the
front cover.  Keep this manual and invoice in a safe and dry place for future reference.

GENERAL SAFETY RULES

WARNING!

SAVE THESE  INSTRUCTIONS

WORK AREA

1.

Keep your work area clean and well lit.  Cluttered and dark areas invite
accidents.

2.

Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust.  
Power tools create sparks
which may ignite the dust or fumes.

3.

Keep bystanders, children, and visitors away while operating a splitter tool.
Distractions can cause you to lose control.  Protect others in the work area from
debris such as chips and sparks.  Provide barriers or shields as needed.

SKU 93815

PAGE 2

READ AND UNDERSTAND ALL INSTRUCTIONS

Failure to follow  all instructions listed below may result in
electric shock, fire, and/or serious injury.

Summary of Contents for 93815

















Reviews: