Central Pneumatic 4041 Assembly And Operating Instructions Manual Download

Page: 8 / 12

SKU 04041

For Technical Questions, Please Call 1-800-444-3353

Page 8

EXHAUST COVER (#4)

NAILS

(10 GAUGE)

(2-3/16” TO 3-1/2” LONG)

FEEDER SHOE

(#52)

NOSE (#29)

BRACKET A

(#35)

SAFETY (38)

TRIGGER

(#44)

FIGURE B

NOSE (#29)

REV 01/04

To Adjust The Depth To Which A Nail Is Driven

The depth to which a nail is driven is controlled by the Safety (part #38).

(See

Figures B and C).

To adjust the depth of drive, loosen the Screw (part #37). Slide Safety (part #38)
up or down to the desired position. Then, re-tighten the Screw.

Note

: Sliding

Safety (38) upward increases the depth of drive. Sliding Safety downward de-
creases the depth of drive.

(See Figure C)

Test fire a nail, and check its depth of drive. Repeat Step #2 as necessary to
achieve the desired depth of drive.

(See Figure C)

QUICK COUPLER &

AIR SUPPLY HOSE

(NOT INCLUDED)

Summary of Contents for 4041













Search results

Summary of Contents for 4041

Reviews:

Related manuals for 4041

Brands by name

Popular brands

Central Pneumatic 4041, Assembly And Operating Instructions Manual

Search results

Summary of Contents for 4041

Reviews:

Related manuals for 4041

Brands by name

Popular brands