background image

 

          

  !! " # $%! &!'( 

# )* 

)* )* # +" 

 -/ #+ 

5 6! 

7  )8 

: )8 

) ;<<  

 )8 

  

= )8 

*! > 6* 

6* '  ?  )8 

 ; ) 

:@ %- 

 D 

E!! -/ E' 

G* 

I !' % 

 

SPECIFICATIONS TABLE

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures, parts list and
assembly diagram.  Keep your invoice with this manual.  Write the invoice
number on the inside of the front cover.  Keep this manual and invoice in a safe
and dry place for future reference.

GENERAL SAFETY WARNINGS AND PRECAUTIONS

1.

KEEP WORK AREA CLEAN AND DRY.  

Cluttered, damp, or wet work areas

invite injuries.

2.

KEEP CHILDREN AWAY FROM WORK AREA.  

Do not allow children to handle

this product.

3.

STORE IDLE EQUIPMENT.  

When not in use, tools and equipment should be

stored in a dry location to inhibit rust.  Always lock up tools and equipment, and
keep out of reach of children.

4.

DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR
DRUGS.  

Read warning labels on prescriptions to determine if your judgement or

reflexes are impaired while taking drugs.  If there is any doubt, do not attempt to
use this product.

SKU 47915

PAGE 2

Rev 01/03

Summary of Contents for 47915















Reviews: