background image

Page 2

For technical questions, please call 1-888-866-5797.

Item 62913 

        

SAFETY

Op
ERA
TION

M

AINTENANCE

INST
ALLA

TION

Table of Contents

Safety ......................................................... 2
Installation .................................................. 2
Specifications ............................................. 6
Operation ................................................... 10

Maintenance .............................................. 14
Parts List and Diagram .............................. 18
Warranty .................................................... 20

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol.  It is used to alert you to potential 

personal injury hazards.  Obey all safety messages that 

follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,  

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,  

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,  

could result in minor or moderate injury.

Addresses practices not related to personal injury.

Summary of Contents for 62913





















Reviews: