background image

SKU 90234

PAGE 7

SYMBOLOGY

V ~

A

xxxx/min.

Double Insulated

Canadian Standards
Association

Underwriters
Laboratories, Inc.

Volts Alternating Current

Amperes

No Load Revolutions
per Minute (RPM)

no

SPECIFIC SAFETY RULES

1.

Maintain a safe working environment.  Keep the work area well lit.  Make sure
there is adequate surrounding workspace.  Always keep the work area free of
obstructions, grease, oil, trash, and other debris.  Do not use this product in
areas near flammable chemicals, dusts, and vapors.

2.

Maintain labels and nameplates on the Air Compressor.  These carry
important information.  If unreadable or missing, contact Harbor Freight Tools for
a replacement.

3.

Use eye and hearing protection.  Always wear ANSI approved safety impact
eye goggles and hearing protectors when using this product.

4.

Do not allow children to use or play with this product.

5.

Store idle equipment.  When not in use, tools and equipment should be stored
in a dry location to inhibit rust.  Always lock up tools and equipment, and keep out
of reach of children.

6.

Do not use this product if under the influence of alcohol or drugs.  Read
warning labels on prescriptions to determine if your judgement or reflexes are
impaired while taking drugs.  If there is any doubt, do not attempt to use this
product.

7.

Make sure to fill the Air Compressor with a premium quality, 30-weight,
non-detergent, compressor oil before each use.  
Running the Air Compressor
with no oil or low oil will cause damage to the equipment and void the warranty.

Summary of Contents for 90234

















Reviews: