background image

Page 2

For technical questions, please call 1-888-866-5797.

Item 93755 

        

SA

FE

TY

OP
ERA

TI

O

N

MAINT

ENANC

E

SE

TUP

Table of Contents

Safety ........................................................................2
Specifications ............................................................5
Setup .........................................................................6
Operation ..................................................................11

Maintenance .............................................................12
Parts List and Diagram .............................................14
Warranty ...................................................................16

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol.  It is used to alert you to potential 

personal injury hazards.  Obey all safety messages that 

follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,  

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,  

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,  

could result in minor or moderate injury.

Addresses practices not related to personal injury.

IMPORTANT SAFETY INSTRUCTIONS

Read all safety warnings and instructions.  

Failure to follow the warnings and instructions may result in serious injury. 

Work Area

1. 

Keep the work area clean and well lit.  

Cluttered 

benches and dark areas increase the risks of 

electric shock, fire, and injury to persons.

2. 

Do not operate the tool in explosive 

atmospheres, such as in the presence 

of flammable liquids, gases, or dust.

  

The tool is able to create sparks resulting 

in the ignition of the dust or fumes.

3.  The work area should have adequate 

drainage to reduce the possibility of 

a fall due to slippery surfaces.

4. 

Keep bystanders, children, and visitors 

away while operating.  

Distractions 

can cause loss of control.

Personal Safety

1. 

Follow all guidelines regarding materials 

being extracted, including MSDS 

instructions and EPA regulations. 

2. 

Stay alert.  Watch what you are doing and use 

common sense when operating.  Do not use 

while tired or under the influence of drugs, 

alcohol, or medication.  

A moment of inattention 

while operating may result in serious personal injury.

Summary of Contents for 93755

















Reviews: