background image

SKU 94275        

For technical questions, please call 1-800-444-3353. 

PAGE 6

11. 

Always unplug the Dust Reclaimer from its electrical outlet before  

 

 

           performing any maintenance or changing accessories.

12. 

Do not use the Dust Reclaimer with any openings blocked.  Keep free of  

 

           anything that may reduce air flow or hinder motor operation.

13. 

Do not use the Reclaimer without its Filter (18) in place.  Before each use,    

           make sure the Filter is cleaned of excess debris.

14. 

This product is designed only to pick up dry debris.  Do not use the Dust    

           Reclaimer to pick up water (or any other liquid) from the floor or containers   
           such as sinks, tubs, barrels, etc.

15. 

When mounting the Dust Reclaimer to a wall surface, make sure the wall    

           and the mounting hardware used (not included) are capable of supporting    
           the weight of the Dust Reclaimer and its contents.

16. 

Prior to drilling mounting holes in a wall surface, check to make sure there   

           are no hidden electrical cables, gas or plumbing pipes in the drilling path.

17. 

       WARNING!  This Dust Reclaimer is not intended for use with silica  

 

           based abrasives.  Silica based abrasives have been linked to severe respiratory   
           disease such as silicosis.  Always use silica substitutes such as aluminum oxide,   
           glass bead, walnut shell, or brass bead.

18. 

        WARNING!  People with pacemakers should consult their physician(s) be-
fore using this product.  Operation of electrical equipment in close proximity to a 
heart pacemaker could cause interference or failure of the pacemaker.

19. 

        WARNING!  The warnings and cautions discussed in this manual cannot 
cover all possible conditions and situations that may occur.  It must be understood 
by the operator that common sense and caution are factors which cannot be built 
into this product, but must be supplied by the operator.

         
                  

9. 

Industrial applications must follow OSHA guidelines.

10. 

Do not allow children to handle or play with this product.

8. 

Never leave the Dust Reclaimer unattended when it is plugged into an

electrical outlet.   Turn off the tool, and unplug it from its electrical outlet before    
leaving.

20.      

Do not handle the Power Cord Plug (12) with wet hands.  Never plug the  

 

           Power Cord of this product into an electrical outlet while standing on a wet   
 

on a wet or damp surface.

Summary of Contents for 94275






















Reviews: