background image

Page 5

SKU 95370

for technical questions, please call 1-800-444-3353.

SPECIfIC SAfETy RuLES

Maintain labels and nameplates on the Air Compressor. 

These carry important 

information.  If unreadable or missing, contact Harbor Freight Tools for a replace-
ment.

Always wear safety impact eye goggles and heavy work gloves when using the 
Air Compressor. 

Using personal safety devices reduce the risk for injury. Safety im-

pact eye goggles and heavy work gloves are available from Harbor Freight Tools.

Maintain a safe working environment.  

Keep the work area well lit.  Make sure 

there is adequate surrounding workspace.  Always keep the work area free of ob-
structions, grease, oil, trash, and other debris.  Do not use a power tool in areas 
near flammable chemicals, dusts, and vapors.  Do not use this product in a damp 
or wet location.

Avoid unintentional starting.  

Make sure you are prepared to begin work before 

turning on the Air Compressor.

do not force the Air Compressor. 

This tool will do the work better and safer at 

the pressure and capacity for which it was designed.  

Always unplug the Air Compressor from its electrical outlet before performing 
any inspection, maintenance, or cleaning procedures, or when not in use.

before each use, check all nuts, bolts, and screws for tightness. Vibration may 
cause these to loosen

.

drain compressor every day.

  Do not allow moisture to build up inside the com-

pressor. 

Make sure all equipment is rated to the appropriate capacity.  

Adjust the output 

air pressure to the tool’s operating capacity.

Avoid explosions and fire

. Never place flammable objects near the compressor. 

Never spray water or any flammable liquids towards the compressor.

Avoid body injury

. Never direct the air outlet at persons or animals. 

Never leave the air tool unattended when it is plugged into the air compressor.

   

Turn off the tool, and unplug it from air compressor outlet before leaving.

  WARNING:

  

People with pacemakers should consult their physician(s) before using 

this product.  Electromagnetic fields in close proximity to a heart pacemaker could 
cause interference to or failure of the pacemaker. 

  

WARNING:  The brass components of this product contain lead, a chemical known to 

the State of California to cause birth defects (or other reproductive harm). (California 
Health & Safety code § 25249.5, et seq.)

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

Summary of Contents for 95370

















Reviews: