background image

SKU 95386

For technical questions, please call 1-800-444-3353.

Page 8

SPECIFIC SAFETY RULES

1.

Maintain a safe working environment.  

Keep the work area well lit.  Make sure

there is adequate surrounding workspace.  Always keep the work area free of
obstructions, grease, oil, trash, and other debris.  Do not use this product in areas
near flammable chemicals, gasoline, dusts and vapors.

2.

Maintain labels and nameplates on the Air Compressor.

  These carry

important information.  If unreadable or missing, contact Harbor Freight Tools for a
replacement.

3.

Use eye and hearing protection.  

Always wear ANSI-approved safety impact

eye goggles and hearing protectors when using this product.

4.

Do not allow children to use or play with this product.

5.

Store idle equipment.  

When not in use, tools and equipment should be stored in

a dry location to inhibit rust.  Always lock up tools and equipment, and keep out of
reach of children.

6.

Do not use this product if under the influence of alcohol or drugs.  

Read

warning labels on prescriptions to determine if your judgement or reflexes are
impaired while taking drugs.  If there is any doubt, do not attempt to use this
product.

7.

Make sure to fill the Air Compressor with a premium quality, 30-weight,
non-detergent, compressor oil before each use.  

Running the Air Compressor

with no oil or low oil will cause damage to the equipment and void the warranty.

SYMBOLOGY

Summary of Contents for 95386

















Reviews: