background image

SKU 95498 

For technical questions, please call 1-800-444-3353. 

Page 15

LIMITEd 1 YEAR / 90 dAY WARRANTY

Harbor Freight Tools Co. makes every effort to assure that its products meet high 

quality and durability standards, and warrants to the original purchaser that for a period 

of one year from date of purchase that the tank is free of defects in materials and work-

manship (90 days if used by a professional contractor or if used as rental equipment).  

Harbor Freight Tools also warrants to the original purchaser, for a period of ninety days 

from date of purchase, that all other parts and components of the product are free from 

defects in materials and workmanship.  This warranty does not apply to damage due di-

rectly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations out-

side our facilities, normal wear and tear, or to lack of maintenance. We shall in no event 

be liable for death, injuries to persons or property, or for incidental, contingent, special 

or consequential damages arising from the use of our product. Some states do not allow 

the exclusion or limitation of incidental or consequential damages, so the above limita-

tion of exclusion may not apply to you.  THIS WARRANTY IS ExPRESSLY IN LIEU OF 

ALL OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDING THE WARRANTIES 

OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with 

transportation charges prepaid. Proof of purchase date and an explanation of the com-

plaint must accompany the merchandise. If our inspection verifies the defect, we will ei

-

ther repair or replace the product at our election or we may elect to refund the purchase 

price if we cannot readily and quickly provide you with a replacement. We will return re-

paired products at our expense, but if we determine there is no defect, or that the defect 

resulted from causes not within the scope of our warranty, then you must bear the cost 

of returning the product.

This warranty gives you specific legal rights and you may also have other rights 

which vary from state to state.

3491 Mission Oaks Blvd.  •  PO Box 6009  •  Camarillo, CA 93011  •  (800) 444-3353

Summary of Contents for 95498
















Reviews: