background image

Page 5

For technical questions, please call 1-888-866-5797.

Item 69269 

        

SAFETY

OPERA

TION

MAINTENANCE

SETUP

Grounding

TO PREVENT ELECTRIC SHOCK AND DEATH  

FROM INCORRECT GROUNDING WIRE CONNECTION: 

Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.  

Do not modify the power cord plug provided with the compressor.   

Never remove the grounding prong from the plug.  Do not use the compressor if the power cord or plug is 

damaged.  If damaged, have it repaired by a service facility before use.  If the plug will not fit the outlet, have a 

proper outlet installed by a qualified electrician.

110-120 VAC Grounded Compressors: 

Compressors with Three Prong Plugs

1.  In the event of a malfunction or breakdown, 

grounding provides a path of least resistance for 

electric current to reduce the risk of electric shock.   

This compressor is equipped with an electric 

cord having an equipment-grounding conductor 

and a grounding plug.  The plug must be 

plugged into a matching outlet that is properly 

installed and grounded in accordance 

with all local codes and ordinances.

2.  Do not modify the plug provided –  

if it will not fit the outlet, have the proper 

outlet installed by a qualified electrician.

3.  Improper connection of the equipment-grounding 

conductor can result in a risk of electric shock.  

The conductor with insulation having an outer 

surface that is green with or without yellow 

stripes is the equipment-grounding conductor.  

If repair or replacement of the electric cord or 

plug is necessary, do not connect the equipment-

grounding conductor to a live terminal.

4.  Check with a qualified electrician or service 

personnel if the grounding instructions are 

not completely understood, or if in doubt as to 

whether the compressor is properly grounded.

5.  Use only 3-wire extension cords that have 

3-prong grounding plugs and 3-pole receptacles 

that accept the compressor’s plug.

6.  Repair or replace damaged or worn cord immediately.

125 VAC 3-Prong Plug and Outlet

(for up to 125 VAC and up to 15 A)

Grounding 

Pin

7.  This compressor is intended for use on a 

circuit that has an outlet that looks like the one 

illustrated above in 

125 VAC 3-Prong Plug 

and Outlet

.  The compressor has a grounding 

plug that looks like the plug illustrated above 

in 

125 VAC 3-Prong Plug and Outlet

.

8.  The outlet must be properly installed and grounded 

in accordance with all codes and ordinances.

9.  Do not use an adapter to connect this 

compressor to a different outlet.

Symbology

PSI

Pounds per square inch of pressure

CFM

Cubic Feet per Minute flow

SCFM

Cubic Feet per Minute flow 

at standard conditions

NPT

National pipe thread, tapered

NPS

National pipe thread, straight

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

VAC

Volts Alternating Current

A

Amperes

Summary of Contents for CentralPneumatic 69269

































Reviews: