background image

15

Never use the RDO unless the Garage Door is in full view and free from objects such as cars,
children and/or adults.

16

Never allow children to operate the RDO.

17. Never operate the RDO when children/persons are under or near the path of the door. Children

be supervised at all times when near the Garage Door and when the RDO is in use.

.

.

must

18. Never attempt to disengage the RDO to manual operation when there are children/persons or

and other objects including motor vehicles under or near the path of the Garage Door.

19. Never attempt to open or close the Garage Door by pulling on the Manual Release Cord.
20. Never attempt to make any repairs or remove covers from the RDO without first disconnecting

the power supply cord from main power supply.

21. For additional safety we strongly recommend the fitment of Safety Beams. Although the RDO

incorporates a pressure sensitive safety obstruction system, the addition of Safety Beams will
greatly enhance the operating safety of the Automatic Garage Door and provide additional
peace of mind. In some countries it is mandatory by law to fit Safety Beams. It is the sole
responsibility of the owner/installer to fit Safety Beams in those countries which so require.

22

Removal of the RDO's protective covers must only be performed by a technically qualified
person. Attempting to remove the protective covers or repair the RDO without suitable technical
qualification may result in severe personal injury, death and/or property damage.

23. Always ensure that the Garage Door is fully open before driving into or out of the Garage.
24. Always ensure the Garage Door is fully closed before leaving the driveway.
25. Adjustments to the Safety Obstruction Force settings must only be carried out by a technically

qualified person. Attempting to adjust the Safety Reverse Force setting without suitable
technical qualification may result in severe personal injury, death and/or property damage.

26. Keep hands and loose clothing clear of the Garage Door and Product at all times.
27. In order for the Safety Obstruction Force System to function it must first encounter an

object/person on to which some force

be exerted. As a result the object/person/door may

suffer

28

MUST

DAMAGE OR INJURY.

The Safety Obstruction Force System is designed to work on STATIONARY objects only. If
the Garage Door encounters a moving object during an Open or Close Cycle, serious
personal injury, death and/or property damage may occur.

.

.

2

IMPORTANT SAFETY RECOMMENDATIONS

Summary of Contents for CS32 RDO






















Reviews: