background image

- 10  

 

 

 

O2X 

DUO 

 

 

 

10.

 

Menu for O2X DUO Sensor 

Use   or   to select the sensor on the main display. The menu for the selected sensor 

is accessed by pressing ENTER for five seconds. If the selected sensor is not active (the 

text 

No transmitter 

is shown) a warning is displayed that asks you to make another 

choice in order to show the sensor menu. 

 

 

Settings 

Tag 

 

Name of the sensor (10 characters) shown on the main display. 

I--Time 

 

Integration time or dampening -- can be set up to 999 seconds. 

Decimals 

1 or 2 for display and menu. 

Analog 

”None” , ”Out1”, ”Out2”, ”Out3”, ”Out4”, ”Out1+2”, or ”Out3+4”. 

Pick which analog output(s) to be used with this sensor. 

Second 

”Temp” or ”=Prim”. If two are chosen above, the first will always 

give the primary value or DO reading according to the sensors 

selected scale. The second will either give the temperature 

scaled as stated below, or the same signal (primary value) as 

the first channel. The temperature is additional information, not 

a precision measurement. 

Temp 0-- 

Temperature scaling, value that will give max output on second 

channel.  Default is 100 C but can be adjusted???? 

Calibrate 

Airpres.mB 

Specify within 10 mBar.  Go to weather station on internet to 

obtain for your zip code or location. 

Calibrate 

”No”, ”Zero”, or ”Air”. Select what calibration to do. 

Temp (info) 

Shows actual temperature in the electrode 

Test (info) 

Shows actual dissolved oxygen level 

Setvalue 

Theoretical reading in air at current temperature and with the 

air pressure entered above. Should be the same as “test” 

immediately after the calibration 

Slope 

Slope of the electrode/cell at last air calibration. 

This value is an indication of the life of the electrode and it is 

normally over 80 for a well functioning Clark electrode. But 

there is nothing that eliminates the possibility of an electrode 

functioning well at lower values. However at values below 50 it 

is recommended to replace the Clark electrode. 

Calibrated 

Date of last air calibration. 

New eletcr. 

Date when electrode/cell was last changed. Push ENTER to edit the 

date, then ENTER again to store it. 

Summary of Contents for O2X Duo





















Reviews: