37
INST
ALLA
TION
AND OPERA
TION MANUAL
BA
THTUB WITH MASSAGE SYSTEM
EN
In order to activate the disinfection process, the following conditions must be fulfilled:
bathtub must be equipped with the massage water system,
bathtub must be filled with water up to a given level,
all its functions must be deactivated,
tank must be filled with a proper disinfectant.
Fulfilling the above conditions facilitates system disinfection according to the following procedure:
Press and hold the pushbutton. until the LEDs on the control panel start to blink.
.
If there is too littleliquid in the tank or the water level in the bathtub
.
is too low, disinfection is stopped after approx. 10 seconds and the
.
display will indicate an error code (Er1 or Er2). The tank must be
.
refilled and the process started again.
Press the pushbutton again stops disinfection process.
.
Time left to the end of the process is indicated on the control panel.
5.6.2 Air system line drying.
This function is used to dry air system lines after the massage is finished. It is activated for 45 seconds . When this time
elapses, it is automatically deactivated. Time left to its end is indicated on the display.
In order to activate this function, the following conditions must be fulfilled:
bathtub must be equipped with the massage air system,
water must be drained from the bathtub,
automatic disinfection function must be deactivated.
Fulfilling the above conditions facilitates system activation of the function according to the following procedure:
1 press activates the air system with 100% intensity.
2 press activates the air system before the automatic drying cycle is finished.
5.6.3 White illumination.
The white illumination function enhances the user’s visual experience during the massage.
In order to activate the illumination, the following conditions must be fulfilled:
bathtub must be filled with water up to a given level,
bathtub must not be equipped with the multicoloured illumination system,
automatic disinfection function must be deactivated.
Fulfilling the above conditions makes it possible to activate the lamp in the following manner:
1 press activates white illumination.
2 press deactivates white illumination.
•
•
•
•
•
•
•
•
•
•
5
SETS EQUIPPED WITH ELECTRONIC CONTROLLERS
Summary of Contents for AirMATIC
