background image

 

 

 

 

 

9 | 

P a g e

 

 

C200 BOX CONTENTS CHECKLIST 

 

C200 Series UPS  

 

USB A to B  

 

Software CD 

 

Power lead 

 

Warranty Card 

 

Telephone patch lead 

 

Quick start guide 

 

 

INSTALLATION  

 

 

 

 

 

DO NOT 

connect the UPS to a mains supply until installation is completed 

 

Ventilation of the UPS is important for proper operation. Ensure the air vents on the front, side and rear of the 

UPS are clear. Allow adequate space around the UPS. The airflow diagram is shown as below: 

 

 

 

 

Installation considerations:  

 

 

The final location of the UPS unit must be on a flat stable surface in a well-ventilated environment 

 

DO 

keep at least 200mm of free space behind the rear panel

 

 

If installing an additional unit, place it next to the first unit in its final location 

 

 

DO 

allow the UPS to reach ambient temperature before turning on

 

 

The UPS needs to be fully charged to achieve full autonomy

 

 

 

 

IF ANY OF THE ITEMS ARE MISSING FROM THE UPS BOX PLEASE NOTIFY YOUR SUPPLIER  

 

DO NOT MAKE ANY UNLICENSED MODIFICATIONS TO THE UPS. THIS MAY INCUR DAMAGE AND AFFECT THE UPS 

WARRANTY. 

 

DO NOT FORGET TO REGISTER THE UPS WARRANTY 

WWW.CERTAUPS.COM/SUPPORT/WARRANTY-REGISTRATION/

 

 

 

Summary of Contents for C200 Series















Reviews: