background image

SECTION 2

OPERATING LIMITATIONS

1. Autopilot OFF during take-off and landing.

2. Maximum airspeed for autopilot operation is 140 KIAS.

3. Required placard, P/N 13A990-1 stating "Conduct trim

check prior to first flight of day (See POH)" to be

installed in clear view of pilot.

4. Category I operations only.

5. Century 2000 Autopilot Operator's Manual, document

#68S1035 dated July 15, 1986, or later applicable

revision must be available to the pilot at all times in the

aircraft when the autopilot is enabled.

SECTION 3

EMERGENCY OPERATING PROCEDURES

3-1 AUTOPILOT

In the event of an autopilot malfunction, or anytime the

autopilot is not performing as commanded, do not attempt to

identify the problem system. Regain control of the aircraft by

overpowering and immediately disconnecting the autopilot. Be

prepared

for any residual trim force and retrim, as necessary,

using the aircraft's primary trim control.

CENTURY FLIGHT SYSTEMS INC.

FAA/DAS APPROVED DATE: 1-22-93

P/N 68S1063

3 of 9

Summary of Contents for 1980 172RG Cutlass
















































































































































































Reviews: